Polaris SLINGSHOT GRAND TOURING 2019 Owner'S Manual Download Page 121

Page: 121 / 147

POSSIBLE CAUSE

POSSIBLE REMEDY/ACTION

Improperly Wired Accessory (Current
Draw)

See dealer to check charging system
output and current draw.

Battery discharges when vehicle not in use. See dealer to check key OFF current draw.

BRAKE NOISE / POOR BRAKE PERFORMANCE

NOTE

Contact your dealer if brake performance does not return after these

inspections.

POSSIBLE CAUSE

POSSIBLE REMEDY/ACTION

Dust / Dirt On Brake Disc(s)

Clean disc.

Worn Pads Or Disc / Brake Disc Damage

Inspect pads.

Brake Fluid Level Low Or Fluid
Contaminated

Inspect fluid level / fluid. See page 89.

ANTI-LOCK BRAKE LIGHT REMAINS ILLUMINATED
OR ILLUMINATES INTERMITTENTLY

POSSIBLE CAUSE

POSSIBLE REMEDY/ACTION

Blown fuse

Check the fuses.

Loose or damaged pulse ring

Inspect pulse ring for looseness or chipped
teeth.

Debris lodged in components

Inspect wheel speed sensor and pulse ring
for debris.

Damage caused by debris

Inspect wheel speed sensor for cracked
housing.

Damaged components

See service manual or authorized dealer.

119

TROUBLESHOOTING

Downloaded from

ManualsNet.com

search engine

Summary of Contents for SLINGSHOT GRAND TOURING 2019




















































































































































Search results

Summary of Contents for SLINGSHOT GRAND TOURING 2019

Reviews:

Related manuals for SLINGSHOT GRAND TOURING 2019

Brands by name

Popular brands

Polaris SLINGSHOT GRAND TOURING 2019, Owner'S Manual

Search results

Summary of Contents for SLINGSHOT GRAND TOURING 2019

Reviews:

Related manuals for SLINGSHOT GRAND TOURING 2019

Brands by name

Popular brands