Polaris SLINGSHOT GRAND TOURING 2019 Owner'S Manual Download Page 115

Page: 115 / 147

6. Store the battery in a dry area with a temperature of 32° to 90° F (0° to 32°

C).

7. While in storage, fully charge the battery once a month.

REMOVAL FROM STORAGE

1. Remove the fabric cover.

2. Remove intake and exhaust opening covers (if covered for storage).

3. Install the tires. Lower the vehicle and remove the jack stands.

4. Verify that tire pressure is at specification. Refer to safety labels on the

vehicle or to the specifications section beginning on page 121.

5. Install the battery and perform an electrical inspection.

6. Inspect the spark plugs. Install new spark plugs if necessary.

7. If the vehicle was stored in an area subject to wide swings in temperature

and humidity (such as outdoors), change the engine oil before starting the
engine.

NOTICE

During storage, temperature and humidity changes can cause condensation to

form in the crankcase and mix with engine oil. Running the engine with oil that

contains condensation can cause engine damage.

8. Inspect the storage area for signs of fluid leaks. Identify and perform service

to any leaking components.

9. Wash and polish the vehicle. Wax, polish or apply protectant to appropriate

components.

10. Perform the pre-ride inspections. See page 47.

11. Check any fluid levels not included in the pre-ride inspection.

113

CLEANING AND STORAGE

Downloaded from

ManualsNet.com

search engine

Summary of Contents for SLINGSHOT GRAND TOURING 2019




















































































































































Search results

Summary of Contents for SLINGSHOT GRAND TOURING 2019

Reviews:

Related manuals for SLINGSHOT GRAND TOURING 2019

Brands by name

Popular brands

Polaris SLINGSHOT GRAND TOURING 2019, Owner'S Manual

Search results

Summary of Contents for SLINGSHOT GRAND TOURING 2019

Reviews:

Related manuals for SLINGSHOT GRAND TOURING 2019

Brands by name

Popular brands