Polaris SLINGSHOT GRAND TOURING 2019 Owner'S Manual Download Page 77

Page: 77 / 147

3. Place a drain pan under the drain plug

4. Remove the drain plug. Allow the fluid to drain completely.

5. Clean and reinstall the drain plug with a new o-ring. Torque to specification.

TORQUE

19-35 ft-lbs (26-48 Nm)

6. Add the recommended fluid. Do not overfill. Maintain the fluid level at the

bottom edge of the fill hole.

FLUID CAPACITY

2.75 qts (2.6 liters)

7. Reinstall the fill plug with a new o-ring. Torque to specification.

TORQUE

19-35 ft-lbs (26-48 Nm)

8. Check for leaks. Dispose of used fluid properly.

MAINTENANCE

Downloaded from

ManualsNet.com

search engine

Summary of Contents for SLINGSHOT GRAND TOURING 2019




















































































































































Search results

Summary of Contents for SLINGSHOT GRAND TOURING 2019

Reviews:

Related manuals for SLINGSHOT GRAND TOURING 2019

Brands by name

Popular brands

Polaris SLINGSHOT GRAND TOURING 2019, Owner'S Manual

Search results

Summary of Contents for SLINGSHOT GRAND TOURING 2019

Reviews:

Related manuals for SLINGSHOT GRAND TOURING 2019

Brands by name

Popular brands