Polaris RZR 570 2013 Service Manual Download Page 167

Page: 167 / 482

9926813 R04 - 2013-2016

RZR

570 Service Manual

4.7

EFI SYSTEM COMPONENT LOCATIONS

Electronic Control Unit (ECU)

- Located behind the driver’s seat.

Temperature and Manifold Absolute Pressure
Sensor (T-MAP)

- Located in the rubber intake boot between the throt-
tle body and the cylinder head.

Crankshaft Position Sensor (CPS)

- Located in the magneto cover on the right-hand
side of the Engine.

Fuel Injectors / Fuel Rail / Regulator

- Attached to the fuel rail located in the intake track of
the cylinder head.

FUEL SYSTEM

Summary of Contents for RZR 570 2013



































































































































































































































































































































































































































































































Search results

Summary of Contents for RZR 570 2013

Reviews:

Related manuals for RZR 570 2013

Brands by name

Popular brands

Polaris RZR 570 2013, Service Manual

Search results

Summary of Contents for RZR 570 2013

Reviews:

Related manuals for RZR 570 2013

Brands by name

Popular brands