Polaris RZR 570 2013 Service Manual Download Page 40

Page: 40 / 482

2.4

9926813 R04 - 2013-2016

RZR

570 Service Manual

MAINTENANCE INTERVALS

ITEM

MAINTENANCE INTERVAL

(WHICHEVER COMES FIRST)

REMARKS

HOURS

CALENDAR

MILES

(KM)

■

Steering

Pre-Ride

Make adjustments as needed.
See Pre-Ride Checklist in this chapter.

▶

Front Suspension

Pre-Ride

▶

Rear Suspension

Pre-Ride

Tires

Pre-Ride

▶

Brake Fluid Level

Pre-Ride

▶

Brake Pedal Travel

Pre-Ride

Brake Systems

Pre-Ride

Wheels / Fasteners

Pre-Ride

Frame Fasteners

Pre-Ride

▶

Engine Oil Level

Pre-Ride

▶

Air Filter

Pre-Ride

Inspect; replace as needed

Coolant Level

Daily

Check level daily, change coolant every 2
years

Head Lamp / Tail Lamp

Daily

Check operation; apply dielectric grease if
replacing

▶

Air Filter

Weekly

Inspect; replace as needed

▶

■

Brake Pad Wear

10 H

Monthly

100 (160)

Inspect periodically

▶

■

Brake Pad Wear / Inspect
Parking Brake Pads (INT’L)

10 H

Monthly

100 (160)

Inspect periodically

▶

■

Parking Brake Cable
Adjustment (INT’L)

25 H

Inspect; adjust tension after first 25 hours

Battery

25 H

Monthly

250 (400)

Check terminals; clean; test

▶

Front Gearcase Oil
(Demand Drive)

25 H

Monthly

250 (400)

Inspect level; change yearly

▶

Transmission - Main
(AGL Gearcase Lubricant)

25 H

Monthly

250 (400)

Inspect level; change yearly

▶

Engine Oil Change
(Break-In Period)

25 H

1 M

250 (400)

Perform a break-in oil change at one month

■

Throttle Cable / Throttle Pedal

50 H

6 M

300 (500)

Inspect; adjust; lubricate; replace if necessary

Throttle Body Air Intake Ducts
/ Flange

50 H

6 M

300 (500)

Inspect ducts for proper sealing / air leaks

▶

General Lubrication

50 H

3 M

500 (800)

Lubricate all fittings, pivots, cables, etc.

Shift Linkage

50 H

6 M

500 (800)

Inspect, lubricate, adjust

■

Steering

50 H

6 M

500 (800)

Lubricate

▶

Front Suspension

50 H

6 M

500 (800)

Lubricate

▶

Rear Suspension

50 H

6 M

500 (800)

Lubricate

Cooling System

50 H

6 M

500 (800)

Inspect coolant strength seasonally; pressure
test system yearly

■

Fuel System

100 H

12 M

600 (1000)

Check for leaks at fill cap, fuel line / rail, and
fuel pump. Replace lines every two years.

■

Spark Plug

100 H

12 M

600 (1000)

Inspect; replace as needed

MAINTENANCE

Summary of Contents for RZR 570 2013



































































































































































































































































































































































































































































































Search results

Summary of Contents for RZR 570 2013

Reviews:

Related manuals for RZR 570 2013

Brands by name

Popular brands

Polaris RZR 570 2013, Service Manual

Search results

Summary of Contents for RZR 570 2013

Reviews:

Related manuals for RZR 570 2013

Brands by name

Popular brands