Polaris RZR 570 2013 Service Manual Download Page 76

Page: 76 / 482

3.4

9926813 R04 - 2013-2016

RZR

570 Service Manual

GENERAL INFORMATION

SPECIAL TOOLS

PART

NUMBER

TOOL DESCRIPTION

PW-47053

Bench Mount Engine Stand Adapter

PU-50658

Clutch Center Distance Tool

PU-50784

Crankshaft Removal / Installation
Tool Kit

PU-50563

Cylinder Holding & Camshaft Timing
Plate

PU-50624

Engine Stand (2” Bore)

PU-50824

Engine Stand Adapter (Mounts To
The Engine)

PU-50625

Engine Stand Sleeve Adapter (Use
With 2” Bore Stand)

PW-47054

Engine Stand Sleeve Adapter (Use
With 2.375” Bore Stand)

PA-49316

Flywheel Puller

PU-50105

Oil Filter Wrench

PV-43531

Oil Pressure Gauge

PU-50569

Oil Pressure Gauge Adapter

PA-49317

Stator Cover Removal Handles

PV-1253

Valve Spring Compressor

PV-43513-A

Valve Spring Compressor Adapter

PU-50689

Water Pump Mechanical / Oil Seal
Installation Kit

Bosch Automotive Service Solutions

: 1-800-328-

6657 or http://polaris.service-solutions.com/

ENGINE LUBRICATION SPECIFICATIONS

FLUID CAPACITY

Oil Capacity:

2 Quarts (1.9 L)

Oil Filter Wrench:

PU-50105 or 2.5″ (64 mm)

Oil Type:

Polaris PS-4 Synthetic Engine Oil

Oil Pressure:

(using Polaris PS-4 at operating temperature)

10 PSI @ 1200 RPM (Minimum)
40 PSI @ 7000 RPM (Minimum)

OIL PRESSURE TEST

Attach the Oil Pressure Gauge Adapter to the Oil
Pressure Gauge.

Oil Pressure Gauge Adapter:

PU-50569

Oil Pressure Gauge:

PV-43531

Remove the seats and engine service panel.

Clean the area around the main oil gallery plug (A),
located on the oil filter adapter housing.

Remove the plug and insert the oil pressure adapter.

Start engine and allow it to reach operating
temperature, monitoring gauge indication.

NOTE

Test results are based on the use of the recommended

engine oil (Polaris PS-4) at operating temperature, and

may vary considerably if any other oil is used or if

engine is not up to temperature.

Upon assembly, torque the crankcase gallery plug to
specification.

TORQUE

Oil Gallery Plug:

12 ft-lbs (16 Nm)

ENGINE / COOLING SYSTEM

Summary of Contents for RZR 570 2013



































































































































































































































































































































































































































































































Search results

Summary of Contents for RZR 570 2013

Reviews:

Related manuals for RZR 570 2013

Brands by name

Popular brands

Polaris RZR 570 2013, Service Manual

Search results

Summary of Contents for RZR 570 2013

Reviews:

Related manuals for RZR 570 2013

Brands by name

Popular brands