Polaris RZR 570 2013 Service Manual Download Page 153

Page: 153 / 482

9926813 R04 - 2013-2016

RZR

570 Service Manual

3.81

Be sure crankshaft is fully seated and rotates
smoothly.

NOTE

The crankshaft seal can be replaced with the engine

installed in the chassis. The engine does not have to be

removed and the crankcase does not have to be

separated to replace the crankshaft seal.

Lubricate a

new

crankshaft seal and slide it over the

PTO end of the crankshaft with numbers facing OUT.
Be sure seal lip does not fold back when moving
over the crankshaft flange.

10. Use the crankshaft removal / installation tool to

properly drive the crankshaft seal into the crankcase.

Crankshaft Removal / Installation Tool

PU-50784

• Center plate

over the crankshaft so it is resting on

the crankshaft seal.

• Center adaptor

over the crankshaft end.

• Place the nut and large washer onto the crankshaft

installation screw.

• Insert the crankshaft installation screw through the

threaded portion of the adaptor.

• Fully thread the crankshaft installation screw into the

clutch bolt threads of the crankshaft.

• Firmly hold the crankshaft installation screw with a

wrench while tightening the large nut against the
adaptor.

11. Drive seal until flush with seal bore.

12. Turn

PTO

crankcase

over

and

support

with

crankshaft upright.

ENGINE / COOLING SYSTEM

Summary of Contents for RZR 570 2013



































































































































































































































































































































































































































































































Search results

Summary of Contents for RZR 570 2013

Reviews:

Related manuals for RZR 570 2013

Brands by name

Popular brands

Polaris RZR 570 2013, Service Manual

Search results

Summary of Contents for RZR 570 2013

Reviews:

Related manuals for RZR 570 2013

Brands by name

Popular brands