Polaris RZR 570 2013 Service Manual Download Page 148

Page: 148 / 482

3.76

9926813 R04 - 2013-2016

RZR

570 Service Manual

CRANKSHAFT REMOVAL

Remove the engine from the engine stand and place
the assembly on a sturdy work bench.

Install the crankshaft removal / installation tool on to
the PTO side crank case.

Crankshaft Removal / Installation Tool

PU-50784

• Install plate

over adapter

• Evenly attach the assembly onto the PTO side

crankcase using the four bolts as shown below.

• Thread the crankshaft removal screw

into

With the help of an assistant holding the crankshaft,
slowly tighten the screw

until the crankcase is

completely separated from the crankshaft.

Remove all special tools from the crankcase.

CRANKSHAFT INSPECTION

NOTE

The connecting rod uses plain bearings. The

connecting rod bearings are not serviceable. If ANY
excessive wear or movement is present or if the rod

does not rotate on the crankshaft freely, the crankshaft

assembly must be replaced.

Use a feeler gauge to measure the connecting rod
big end side clearance

Connecting Rod Big End Side Clearance:

0.00590-.01771″ (.15 - .45mm)

Measure the connecting rod small end I.D.

Small End I.D. Standard:

0.8665 - 0.8670″ (22.010 - 22.023 mm)

Service Limit: 0.08682″ (22.053 mm)

ENGINE / COOLING SYSTEM

Summary of Contents for RZR 570 2013



































































































































































































































































































































































































































































































Search results

Summary of Contents for RZR 570 2013

Reviews:

Related manuals for RZR 570 2013

Brands by name

Popular brands

Polaris RZR 570 2013, Service Manual

Search results

Summary of Contents for RZR 570 2013

Reviews:

Related manuals for RZR 570 2013

Brands by name

Popular brands