Polaris RZR 570 2013 Service Manual Download Page 142

Page: 142 / 482

3.70

9926813 R04 - 2013-2016

RZR

570 Service Manual

STATOR REMOVAL

NOTE

Test stator wire continuity before removing it from the

housing.

Remove the stator cover.

CAUTION

The flywheel contains powerful magnets. Use caution

when removing the stator cover.

DO NOT place fingers between cover and crankcase at

any time during the removal process or injury could

result.

Remove and discard the stator cover gasket.

CAUTION

Be sure engine coolant does not contaminate the

engine oil during stator cover service.

Remove the three bolts

that secure the stator

to the stator cover

Remove the two bolts that secure the stator wire
routing bracket

to the stator cover.

Remove the stator

from the stator cover.

ENGINE / COOLING SYSTEM

Summary of Contents for RZR 570 2013



































































































































































































































































































































































































































































































Search results

Summary of Contents for RZR 570 2013

Reviews:

Related manuals for RZR 570 2013

Brands by name

Popular brands

Polaris RZR 570 2013, Service Manual

Search results

Summary of Contents for RZR 570 2013

Reviews:

Related manuals for RZR 570 2013

Brands by name

Popular brands