Polaris RZR 570 2013 Service Manual Download Page 248

Page: 248 / 482

6.4

9926813 R04 - 2013-2016

RZR

570 Service Manual

SHIFT LEVER / CABLE

SHIFT LEVER REMOVAL

Remove the shift knob cover, retaining screw and
shift knob from the shift lever.

Remove the screws retaining the center console
using a T27 and T30 Torx driver. Remove the
console from the vehicle.

Remove the clip and washer retaining the shift cable
to the shift lever and disconnect the cable end from
the lever.

Remove the retaining ring and slide the shift lever off
the mounting bracket and out from the frame.

Remove both bushings from the shift lever and
service as needed.

SHIFT LEVER INSTALLATION

Perform the removal steps in reverse order to install
the gear shift lever (lever, cable, console, shift knob).

TRANSMISSION

Summary of Contents for RZR 570 2013



































































































































































































































































































































































































































































































Search results

Summary of Contents for RZR 570 2013

Reviews:

Related manuals for RZR 570 2013

Brands by name

Popular brands

Polaris RZR 570 2013, Service Manual

Search results

Summary of Contents for RZR 570 2013

Reviews:

Related manuals for RZR 570 2013

Brands by name

Popular brands