Polaris RZR 570 2013 Service Manual Download Page 311

Page: 311 / 482

9926813 R04 - 2013-2016

RZR

570 Service Manual

7.13

Install

the

upper

pinch

bolt

and

torque

specification.

TORQUE

Ball Joint Pinch Bolts:

23 ft-lb (31 Nm)

Apply grease to drive shaft axle splines.

Install front wheel hub assembly, cone washers, and
hand tighten the castle nut. Install washers with
domed side out.

Torque wheel hub nut to specification and install a

new

cotter pin. Tighten nut slightly if necessary to

align cotter pin holes.

TORQUE

Front Wheel Hub Castle Nut:

80 ft-lb (108 Nm)

Install brake caliper mounting bolts and torque to
specification.

TORQUE

Front Caliper Mounting Bolts:

30 ft-lbs (41 Nm)

CAUTION

New bolts have a pre-applied locking agent which is

destroyed upon removal. Always use new brake caliper

mounting bolts upon assembly.

10. Install wheel and four wheel nuts. Torque wheel nuts

to specification.

TORQUE

Wheel Nuts:

Steel Rims: 27 ft-lbs (37 Nm)

Aluminum Rims: 30 ft-lbs (41 Nm) + 90°

11. Rotate wheel and check for smooth operation. Bend

both ends of cotter pin around end of spindle in
different directions.

FINAL DRIVE

Summary of Contents for RZR 570 2013



































































































































































































































































































































































































































































































Search results

Summary of Contents for RZR 570 2013

Reviews:

Related manuals for RZR 570 2013

Brands by name

Popular brands

Polaris RZR 570 2013, Service Manual

Search results

Summary of Contents for RZR 570 2013

Reviews:

Related manuals for RZR 570 2013

Brands by name

Popular brands