Polaris RZR 570 2013 Service Manual Download Page 239

Page: 239 / 482

9926813 R04 - 2013-2016

RZR

570 Service Manual

5.33

CLUTCH BUSHING INSTALLATION

1. Install Number Two Puller Adapter

onto puller.

2. Install the Adapter Reducer

onto puller.

3. Apply Loctite® 648 evenly to bushing bore inside

moveable sheave.

4. Install sheave face down on puller.

5. Install new bushing on installation tool

and install

assembly into sheave.

6. Install left hand thread nut onto puller rod and hand

tighten against installation tool.

7. Turn clutch sheave counterclockwise, making sure

bushing is drawn straight into bore. Continue until
bushing is seated.

8. Remove nut from puller rod and set aside.

9. Remove installation tool and clutch sheave from

puller.

DRIVEN CLUTCH ASSEMBLY

1. Install a new bearing

onto the clutch shaft using an

arbor press. Once bearing is fully seated, install a
new snap ring

2. Install the shaft and bearing assembly into the outer

sheave using an arbor press.

NOTE

Press only on the outer race of the bearing during

installation to prevent damaging the bearing.

PVT SYSTEM

Summary of Contents for RZR 570 2013



































































































































































































































































































































































































































































































Search results

Summary of Contents for RZR 570 2013

Reviews:

Related manuals for RZR 570 2013

Brands by name

Popular brands

Polaris RZR 570 2013, Service Manual

Search results

Summary of Contents for RZR 570 2013

Reviews:

Related manuals for RZR 570 2013

Brands by name

Popular brands