manualshive.com logo in svg

Polaris RZR 570 2013, Service Manual

The Polaris RZR 570 2013 service manual is available for free download from manualshive.com. This comprehensive manual provides detailed information on maintenance, repair, and troubleshooting for the Polaris RZR 570 2013 model. Download your manual today and ensure your vehicle is running smoothly for years to come.

Share
Download
background image

2

9926813 R04 - 2013-2016

RZR

570 Service Manual

© Copyright Polaris Industries Inc.

2.1

MAINTENANCE

CHAPTER 2

MAINTENANCE

PERIODIC MAINTENANCE CHART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.3

PERIODIC MAINTENANCE OVERVIEW

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.3

BREAK-IN PERIOD

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.3

MAINTENANCE CHART KEY

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.3

MAINTENANCE INTERVALS

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.4

MAINTENANCE QUICK REFERENCE

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.6

GREASE LUBRICATION POINTS

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.8

LUBRICANTS / SERVICE PRODUCTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.9

LUBRICANTS / SERVICE PRODUCTS

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.9

GENERAL VEHICLE INSPECTION AND MAINTENANCE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2.10

PRE-RIDE / DAILY INSPECTION

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2.10

FRAME, NUTS, BOLTS, AND FASTENERS

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2.10

ENGINE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.11

ENGINE OIL LEVEL

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.11

ENGINE OIL AND FILTER SERVICE

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.11

ENGINE BREATHER HOSE INSPECTION

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2.13

ENGINE AND TRANSMISSION MOUNTS

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2.13

COMPRESSION TEST SPECIFICATION

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2.13

VALVE CLEARANCE INSPECTION

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2.14

EXHAUST - SPARK ARRESTOR

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2.15

COOLING SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2.16

COOLING SYSTEM OVERVIEW

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2.16

COOLING SYSTEM EXPLODED VIEW

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2.16

COOLANT LEVEL INSPECTION

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2.17

COOLING SYSTEM PRESSURE TEST

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2.17

COOLANT STRENGTH / TYPE

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2.17

COOLING SYSTEM

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2.18

COOLANT DRAIN

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2.18

FUEL SYSTEM AND AIR INTAKE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2.19

FUEL SYSTEM

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2.19

FUEL LINE

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2.19

FUEL PUMP / FUEL FILTERS

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2.19

VENT LINES

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2.20

THROTTLE PEDAL INSPECTION

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2.20

THROTTLE FREEPLAY ADJUSTMENT

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2.20

ENGINE AND PVT INTAKE PRE-FILTER SERVICE

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2.21

AIR FILTER SERVICE

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2.22

PVT / FINAL DRIVE / WHEEL AND TIRE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2.23

WHEEL AND HUB TORQUE TABLE

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2.23

WHEEL REMOVAL

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2.23

WHEEL INSTALLATION

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2.23

TIRE INSPECTION

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2.24

Summary of Contents for RZR 570 2013



































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for RZR 570 2013

Ace Sports Maxxam 150 2R Service Manual preview
Maxxam 150 2R
Brand: Ace Sports Pages: 79
Yamaha MM600D Owner'S Manual preview
MM600D
Brand: Yamaha Pages: 84
GAS GAS QUAD - PART LIST 2007 Parts List preview
QUAD - PART LIST 2007
Brand: GAS GAS Pages: 77
Toro 130-5615 Installation Instructions Manual preview
130-5615
Brand: Toro Pages: 20
HER CHEE 2002/24 ATV-300XS Service Manual preview
2002/24 ATV-300XS
Brand: HER CHEE Pages: 56
Polaris RANGER XP 1000 2020 Owner'S Manual preview
RANGER XP 1000 2020
Brand: Polaris Pages: 156
Foldy 750 Series User Manual preview
750 Series
Brand: Foldy Pages: 44
Morooka MST-800VD Operation & Maintenance Manual preview
MST-800VD
Brand: Morooka Pages: 134
Fuelfix Tanks2Go 1200lt Mobile Fuel Tank Trailer User Manual preview
Tanks2Go 1200lt Mobile Fuel Tank Trailer
Brand: Fuelfix Pages: 17
Can-Am 2009 Outlander 500 EFI Operator'S Manual preview
2009 Outlander 500 EFI
Brand: Can-Am Pages: 152
Cectec ESTOC Service Manual preview
ESTOC
Brand: Cectec Pages: 212
LONCIN LX50ATV-2 Kitten Owner'S Manual preview
LX50ATV-2 Kitten
Brand: LONCIN Pages: 129
Polaris Sportsman 9920364 Owner'S Manual preview
Sportsman 9920364
Brand: Polaris Pages: 143
Taylor-Dunn B0-050-00 Operation, T Roubleshooting And Replacement Parts Manual preview
B0-050-00
Brand: Taylor-Dunn Pages: 233
Yamaha Warrior YFM350XRC Owner'S Manual preview
Warrior YFM350XRC
Brand: Yamaha Pages: 174
FARMA T 12 Instruction Book preview
T 12
Brand: FARMA Pages: 13
MANCO 8090 Owner'S/Operator'S Manual preview
8090
Brand: MANCO Pages: 20
BRP Can-Am DS 450 EFI 2009 Predelivery Bulletin preview
Can-Am DS 450 EFI 2009
Brand: BRP Pages: 19

Brands by name

Popular brands

Load more brands