manualshive.com logo in svg

Polaris RZR 570 2013, Service Manual

The Polaris RZR 570 2013 service manual is available for free download from manualshive.com. This comprehensive manual provides detailed information on maintenance, repair, and troubleshooting for the Polaris RZR 570 2013 model. Download your manual today and ensure your vehicle is running smoothly for years to come.

Share
Download
background image

4

9926813 R04 - 2013-2016

RZR

570 Service Manual

© Copyright Polaris Industries Inc.

4.1

FUEL SYSTEM

CHAPTER 4

FUEL SYSTEM

GENERAL INFORMATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.3

SPECIAL TOOLS

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.3

SERVICE NOTES

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.5

EFI SYSTEM EXPLODED VIEW

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.6

EFI SYSTEM COMPONENT LOCATIONS

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.7

EFI SYSTEM ELECTRICAL DIAGRAM

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.9

EFI OVERVIEW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4.10

PRINCIPAL COMPONENTS

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4.10

EFI OPERATION OVERVIEW

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4.10

INITIAL PRIMING / STARTING PROCEDURE

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4.10

ELECTRONIC CONTROL UNIT (ECU) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.11

OPERATION OVERVIEW

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.11

ECU SERVICE

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4.12

ECU REPLACEMENT

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4.12

ECU REPLACEMENT

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4.12

FUEL INJECTORS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4.13

OPERATION OVERVIEW

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4.13

FUEL INJECTOR TROUBLESHOOTING

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4.13

FUEL INJECTOR TEST

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4.14

FUEL INJECTOR REPLACEMENT

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4.14

FUEL TANK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4.16

FUEL LINES - QUICK CONNECT

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4.16

EXPLODED VIEW

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4.17

OPERATION OVERVIEW

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4.18

FUEL SENDER TEST

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4.19

FUEL PUMP TEST

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4.19

FUEL PUMP REPLACEMENT

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4.21

FUEL TANK REMOVAL

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4.24

FUEL TANK INSTALLATION

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4.26

TEMPERATURE AND MANIFOLD ABSOLUTE PRESSURE SENSOR (T-MAP) . . . . . . . . . . . . . . . . . . . .4.27

OPERATION OVERVIEW

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4.27

T-MAP SENSOR TEST

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4.27

T-MAP SENSOR REPLACEMENT

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4.27

IDLE AIR CONTROL (IAC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4.28

OPERATION OVERVIEW

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4.28

IAC TEST

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4.28

IAC REPLACEMENT

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4.28

THROTTLE POSITION SENSOR (TPS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4.29

OPERATION OVERVIEW

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4.29

TPS RESISTANCE TESTS

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4.29

TPS TESTER / REGULATOR

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4.30

TPS REPLACEMENT

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4.30

Summary of Contents for RZR 570 2013



































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for RZR 570 2013

Honda 1995 Fourtrax 300 Owner'S Manual preview
1995 Fourtrax 300
Brand: Honda Pages: 156
Coleman AT200-B Assembly Instructions Manual preview
AT200-B
Brand: Coleman Pages: 12
CAMSO ATV R4S User Manual preview
ATV R4S
Brand: CAMSO Pages: 50
Yamaha Grizzly 80 YFM80GX Owner'S Manual preview
Grizzly 80 YFM80GX
Brand: Yamaha Pages: 134
Yamaha GRIZZLY 80 Owner'S Manual preview
GRIZZLY 80
Brand: Yamaha Pages: 145
Yamaha GRIZZLY 350 YFM35FGY Owner'S Manual preview
GRIZZLY 350 YFM35FGY
Brand: Yamaha Pages: 138
Yamaha GRIZZLY 350 YFM35FGW Owner'S Manual preview
GRIZZLY 350 YFM35FGW
Brand: Yamaha Pages: 138
Yamaha GRIZZLY 350 YFM35GTXG Owner'S Manual preview
GRIZZLY 350 YFM35GTXG
Brand: Yamaha Pages: 140
Yamaha GRIZZLY 350 YFM350AZ Owner'S Manual preview
GRIZZLY 350 YFM350AZ
Brand: Yamaha Pages: 138
Yamaha GRIZZLY 350 YFM35FGIA Owner'S Manual preview
GRIZZLY 350 YFM35FGIA
Brand: Yamaha Pages: 146
Yamaha GRIZZLY 700 FI YFM7FGPY Owner'S Manual preview
GRIZZLY 700 FI YFM7FGPY
Brand: Yamaha Pages: 164
Yamaha GRIZZLY 350 YFM35FGDW Owner'S Manual preview
GRIZZLY 350 YFM35FGDW
Brand: Yamaha Pages: 144
Yamaha GRIZZLY 350 YFM35FGDZ Owner'S Manual preview
GRIZZLY 350 YFM35FGDZ
Brand: Yamaha Pages: 148
Yamaha GRIZZLY 350 YFM350FAD Owner'S Manual preview
GRIZZLY 350 YFM350FAD
Brand: Yamaha Pages: 144
Yamaha GRIZZLY 700 FI YFM7FGPW Owner'S Manual preview
GRIZZLY 700 FI YFM7FGPW
Brand: Yamaha Pages: 166
Yamaha Grizzly 600 Owner'S Manual preview
Grizzly 600
Brand: Yamaha Pages: 164
Yamaha Grizzly 700 YFM7FGPA Owner'S Manual preview
Grizzly 700 YFM7FGPA
Brand: Yamaha Pages: 172
Yamaha grizzly 700 Owner'S Manual preview
grizzly 700
Brand: Yamaha Pages: 170

Brands by name

Popular brands

Load more brands