Phytec phyCORE-OMAP44 Series Hardware Manual Download Page 56 | Manualshive

Page: 56 / 168

background image

Part I: PCM-049/phyCORE-OMAP44xx System on Module

phyCORE-OMAP44xx

44

©

PHYTEC Messtechnik GmbH

2012

L-760e_1

1.6.2 NAND Flash Memory (U4)

Use of Flash as non-volatile memory on the phyCORE-OMAP44xx provides an easily reprogrammable means of
code storage. The following Flash device can be used on the phyCORE-OMAP44xx:

Additionally, any parts that are footprint (VFBGA) and functionally compatible with the NAND Flash devices
listed above may also be used with the phyCORE-OMAP44xx.

The Flash device is programmable with 1.8 V. No dedicated programming voltage is required.

As of the printing of this manual NAND Flash devices generally have a life expectancy of at least 100,000 erase/
program cycles and a data retention rate of 10 years.

The NAND Flash memory is connected to the GPMC bus.

1.6.2.1 NAND Flash Lock Control (J4)

Jumper J4 controls the block lock feature of the NAND Flash (U4). Setting this jumper to position 2 + 3 enables
the block lock commands and protects or locks all blocks of the device, while position 1 + 2 or removing this
jumper will disable the block lock commands. Block lock feature can only enabled or disabled at power-on of the
NAND Flash device. The following configurations are possible:

Manufacturer

NAND Flash P/N

Density

Bus Width

Micron

MT29F1G08ABBDAH4

128 MB

8 Bit

Micron

MT29F4G08ABBDAH4

512 MB

8 Bit

Micron

MT29F8G16ADBDAH4

1 GB

16 Bit

Table 11:

Compatible NAND Flash Devices

NAND Flash lock state

J4

Block lock commands disabled

1 + 2 or not mounted

Block lock commands enabled

2 + 3

Table 12:

NAND Flash Lock Control via J4

1

1.

Defaults are in

bold blue

text

«
...
54
55
56
57
58
...
»

Summary of Contents for phyCORE-OMAP44 Series









































































































































































Reviews:

No comments

Related manuals for phyCORE-OMAP44 Series

Brand: IBM Pages: 357

Brand: ST Pages: 9

Brand: ECS Pages: 93

Brand: Texas Instruments Pages: 13

DUOX Programmer

Brand: Fermax Pages: 99

Brand: Ublox Pages: 25

Brand: OpenVox Pages: 29

Brand: JETWAY Pages: 45

Brand: ASROCK Pages: 97

Brand: Gigabyte Pages: 96

Super 7 SY-5SSM

Brand: SOYO Pages: 86

Brand: Supermicro Pages: 126

Brand: Gigabyte Pages: 39

Brand: Gigabyte Pages: 80

STEVAL-IHM022V1

Brand: ST Pages: 58

Brand: Atmel Pages: 74

Brand: Foxconn Pages: 106

Brand: TYAN Pages: 73

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands