Panasonic Windea VGD13113W Simple Manual Download Page 88

Page: 88 / 118

OPEN

FIRE

Not Home

OPEN

NOT HOME

GAS

●

If the entered security number is correct, the

Security SET indicator turns off, and the

security alarm is disarmed.

After the security disarmed message is

triggered, and the "Security has been turned

off." message appears on the screen, the

Top Menu screen appears. (The Mode

Change screen appears instead if using

Living mode. Select Living mode.)

●

If the entered security number is incorrect,

the system returns to the "Enter the security

number." screen. If this happens, repeat the

procedure from Step .

●

All security system alarms are disarmed when this
procedure is performed.
(This is also applicable when the "Security
Individual Alarm" is enabled.)

●

The security disarmed message can be
disabled or changed to a simple
sound alarm.

Security Off Sound
settings ( Page 108)

Security Alarm Activations

171

Activating the Emergency Alarm

Confirm that system components are properly installed before using the system.

Disarming Security Alarms (disable any active security and security preliminary alarms) (for Base Unit)

If the EMERGENCY Button or Other Emergency Button is Pressed

●

The entered security number appears.

Press the EMERGENCY button again

The EMERGENCY button turns off.

How to reset the EMERGENCY button
on the base unit and call sub-base unit

●

The alarm sound can be disabled.

The alarm display for the Emergency

icon etc. will still appear on the

display, or the report will be sent.

●

Reports made to the building

manager room and door phone can

be delayed by approximately

30 seconds.

Consult with the management

company or the company that

installed the system.

Installer

setting

Open the Emergency button and reset

the protection board.

Press to
reset.

Remove the cover.
Pull the button forward.

Reposition the protection board back
to its original position and place it
inside the main unit.

Back of the cover

Protection board

Press the button or pull the drawstring
again.

1
2

Cover

Button

How reset other Emergency buttons

Model WTF4510W

If the EMERGENCY button or other Emergency button is pressed, the system
reports the state of emergency.

●

Press the STOP ALARM button.

The alarm can be also be turned off

from the building manager room.

How to stop the alarm sound

Procedures during alarms

Touch on the base unit
while the preliminary security alarm
or security alarm is active

Enter the security number

Touch

Security SET

indicator flashes

in green

●

When using Living mode

●

The figure illustrates an example of entering "1234".

●

The "Enter the security number." screen

appears.

●

Security alarms are disarmed if no

security number has been configured.

Step and subsequent steps do not

need to be performed.

Touch

the numeric

buttons

●

The Emergency icon will turn off after

approximately 3 minutes, and the area around

the MENU button will flash in red.

●

If the pressed EMERGENCY button is reset,

the alarm stops. Also, the area around the

MENU button, ALARM indicator on the call

sub-base unit, and door phone alarm display

indicator turn off.

●

The EMERGENCY button, area around the
MENU button, and alarm display indicator
continues to flash until the pressed
EMERGENCY button is reset.

●

The emergency icon can also be turned off
within 3 minutes. ( Page 155)

●

If some other Emergency button is pressed,
the EMERGENCY buttons on the base unit
and sub-base unit do not flash.

●

Confirm the alarm

details and then

perform the appropriate

procedures such

as notifying

neighbors.

INTRODUCTION

USUAL USAGE

SETTING ACCORDING TO

YOUR PREFERENCES

OPERATIONS AND MEASURES

WHEN ALARM GOES OFF

SECURITY ALARM SETTING

AND DISARMING

RECORD

MANAGEMENT

OTHER

Touch

電源

POWER

警戒

SET

非常

EMERG.

Note

170

復旧/警報音停止

RESET/ STOP ALARM

電源

POWER

●

The security alarm and security preliminary alarm
remain active if no operation is performed for 10
seconds. If this happens, repeat the procedure
from Step .

●

Touch if in the security number is entered
incorrectly. All numbers will be cleared.

Note

Door phone

Alarm display indicator
Flashes in red
Alarm is sounding

EMERGENCY button

flashes in red

(Siren)

Emergency.

MENU button

STOP ALARM button

Emergency icon

flashes in red

Call sub-base unit

ALARM indicator
Flashes in red
Alarm is sounding

does not appear in the call sub-base
unit with monitor.

●

For base unit

Touch

any one

Note

復旧

警報音停止

RESET/ STOP ALARM

電源

POWER

復旧/警報音停止

非常

EMERG.

Note

Summary of Contents for Windea VGD13113W























































































































Search results

Summary of Contents for Windea VGD13113W

Reviews:

Related manuals for Windea VGD13113W

Brands by name

Popular brands

Panasonic Windea VGD13113W, Simple Manual

Search results

Summary of Contents for Windea VGD13113W

Reviews:

Related manuals for Windea VGD13113W

Brands by name

Popular brands