manualshive.com logo in svg

Panasonic KX-UTG200, Setup Manual, Page: 95 / 412

Share
Download
Panasonic KX-UTG200 Setup Manual Download Page 95

Value Range

•

1–5

Note

•

Refer to the following for voice quality values.

–

5: Perfect. Like face-to-face conversation or radio
reception.

–

4.5: Network or toll quality.

–

4: Good. Imperfections can be perceived, but sound is
clear.

–

3.5: Cell phone quality.

–

2.5: Voices sound synthetic.

–

2: Poor. Nearly impossible to communicate.

–

1: Bad. Impossible to communicate.

Default Value

Not applicable.

4.3  Network

This section provides detailed descriptions about all the settings classified under the 

[Network]

 tab.

4.3.1  Basic Network Settings

This screen allows you to change basic network settings such as whether to use a DHCP server, and the IP
address of the unit.

Note

•

Changes to the settings on this screen are applied when the message "Save Complete!" appears after
clicking 

[Save]

. Because the IP address of the unit will probably be changed if you change these

settings, you will not be able to continue using the Web user interface. To continue configuring the unit
from the Web user interface, log in to the Web user interface again after confirming the newly assigned
IP address of the unit using the phone user interface. In addition, if the IP address of the PC from which
you try to access the Web user interface has been changed, close the Web port once by selecting
"

Off

" for "

Embedded web

" on the unit (

®

 see 

Opening/Closing the Web Port

 in 

1.1.5.2  Before

Accessing the Web User Interface

).

Document Version  2015-01  

Administrator Guide

95

4.3.1 Basic Network Settings

Summary of Contents for KX-UTG200





























































































































































































































































































































































































































Reviews:

No comments