manualshive.com logo in svg

Panasonic KX-UTG200, Setup Manual, Page: 30 / 412

Share
Download
Panasonic KX-UTG200 Setup Manual Download Page 30

Note

•

If your phone system dealer does not allow you these settings, you cannot change them even though
the unit shows the setting menu. Contact your phone system dealer for further information.

•

If you select "DHCP"/"Enable IPv6 DHCP" for the connection mode, all the settings concerning static
connection will be ignored, even if they have been specified.

•

If you enable "DHCP"/"Enable IPv6 DHCP" for the connection mode and "Auto DNS"/"IPv6 Auto
DNS" for DNS, the DNS server settings (DNS1 and DNS2) will be ignored, even if they have been
specified.

1.1.3  Overview of Programming

There are 3 types of programming, as shown in the table below:

Programming

Type

Description

References

Phone user
interface
programming

Configuring the unit’s settings directly from the unit.

®

 1.1.4  Phone User Interface

Programming

®

 Section  3  Phone User

Interface Programming

Web user
interface
programming

Configuring the unit’s settings by accessing the Web
user interface from a PC connected to the same
network.

®

 1.1.5  Web User Interface

Programming

®

 Section  4  Web User

Interface Programming

Configuration file
programming

Configuring the unit's settings by creating
configuration files and having the unit download the
files from a server on the Internet.

®

 Section  2  Provisioning

®

 Section  5  Configuration

File Programming

1.1.4  Phone User Interface Programming

You can change the settings directly from the unit.
For details about the operations, refer to the Operating Instructions on the Panasonic Web site (

®

 see

Introduction

).

For details about additional features available with direct commands, see 

Section  3  Phone User Interface

Programming

.

30

Administrator Guide

Document Version  2015-01  

1.1.4 Phone User Interface Programming

Summary of Contents for KX-UTG200





























































































































































































































































































































































































































Reviews:

No comments