Panasonic KX-UTG200 Setup Manual Download Page 103

Page: 103 / 412

4.3.4.1 Link Speed/Duplex Mode

LAN Port

Description

Selects the connection mode (link speed and duplex mode) of the LAN
port.

Value Range

•

Auto Negotiation

•

1000 Mbps/Full Duplex

•

100 Mbps/Full Duplex

•

100 Mbps/Half Duplex

•

10 Mbps/Full Duplex

•

10 Mbps/Half Duplex

Default Value

Auto Negotiation

PC Port

Description

Selects the connection mode (link speed and duplex mode) of the PC
port.

Value Range

•

Auto Negotiation

•

1000 Mbps/Full Duplex

•

100 Mbps/Full Duplex

•

100 Mbps/Half Duplex

•

10 Mbps/Full Duplex

•

10 Mbps/Half Duplex

Default Value

Auto Negotiation

4.3.4.2 LLDP Settings

Enable LLDP

Description

Selects whether to enable or disable sending and receiving LLDP
frames.

Note

•

You should specify "

Yes

" for only one of "

VLAN

", "

LLDP

" or

CDP

•

If "

Yes

" is specified for two or more of the parameters above,

the settings are prioritized as follows: "

VLAN

" > "

LLDP

" >

CDP

". Therefore, if "

Yes

" is specified for both "

VLAN

" and

LLDP

", the VLAN-related settings are used.

Value Range

•

Yes

•

Default Value

Yes

Configuration File Reference

LLDP_ENABLE (Page 275)

Document Version 2015-01

Administrator Guide

103

4.3.4 Ethernet Port Settings

Summary of Contents for KX-UTG200





























































































































































































































































































































































































































Search results

Summary of Contents for KX-UTG200

Reviews:

Panasonic KX-UTG200, Setup Manual, Page: 103 / 412

Search results

Summary of Contents for KX-UTG200

Reviews: