Panasonic KX-UTG200 Setup Manual Download Page 343

Page: 343 / 412

SIP_TIMER_T2

Value Format

Integer

Description

Specifies the maximum interval, in seconds, between transmissions of
SIP messages. For details, refer to RFC 3261.

Value Range

•

Default Value

Web User Interface Reference

T2 Timer (Page 128)

SIP_TIMER_T4

Value Format

Integer

Description

Specifies the maximum period, in seconds, that a message can remain
on the network.

Value Range

•

Default Value

SIP_FOVR_NORSP

Value Format

Boolean

Description

Specifies whether to perform the fail-over process when the unit detects
that the SIP server is not replying to SIP message.

Value Range

•

Y/Yes

(Enable fail-over)

•

N/No

(Disable fail-over)

Note

•

If set to "

", the unit will try to use the other SIP servers via the

DNS SRV and A records.

•

If set to "

", the unit will not try to use the other SIP servers.

Default Value

Document Version 2015-01

Administrator Guide

343

5.9.3 Per Line - SIP Settings

Summary of Contents for KX-UTG200





























































































































































































































































































































































































































Search results

Summary of Contents for KX-UTG200

Reviews:

Panasonic KX-UTG200, Setup Manual, Page: 343 / 412

Search results

Summary of Contents for KX-UTG200

Reviews: