Panasonic Aquarea B1 Planning And Installation Manual Download Page 88

Page: 88 / 117

168

Aquarea air-to-water heat pumps - Planning and installation manual - 01/2018

Installation

169

Aquarea air-to-water heat pumps - Planning and installation manual - 01/2018

Installation

Carry out the following steps to connect the outflow hose to the condensation outflow of the

outdoor unit:

Assemble the supplied outlet bend with seal on the condensation outflow on the under

side of the outdoor unit, as shown in the figures below.

Seal the openings on the underside of the outdoor unit (model-dependent number: 7 or 8)

using the supplied rubber sealing caps.

3. Push the hose over the outlet bend.
4.

Ensure that the outflow hose is seated firmly. Use a hose clip to attach the hose, if neces

sary (to be provided on site).

Lay the outflow hose in a constant downward alignment. For large outflow hose lengths,

you may want to use a metal support (provided on site) to prevent the hose from bending.

Detail view from below

1 Condensation outlet

2 Outlet bend

3 Openings

(7 or 8, depending on model)

4 Rubber seal caps

Compact devices

Carry out the following steps to connect the outflow hose to the condensation outflow of the

compact device:

Slide the outflow hose onto the condensation outlet socket on the compact device.

Ensure that the outflow hose is seated firmly. Use a hose clip to attach the hose, if neces

sary (to be provided on site).

Lay the outflow hose in a constant downward alignment. For large outflow hose lengths,

you may want to use a metal support (provided on site) to prevent the hose from bending.

View from below

1 Condensation outlet

6.7.2.1

Connecting the condensation outflow hose

Indoor units

Carry out the following steps to connect the outflow hose to the condensation outflow of the

indoor unit:

Assemble the supplied outlet bend with seal on the condensation outflow on the under

side of the indoor unit, as shown in the illustrations below.

2. Push the hose over the outlet bend.
3.

Ensure that the outflow hose is seated firmly. Use a hose clip to attach the hose, if neces

sary (to be provided on site).

Lay the outflow hose in a constant downward alignment into a suitable collection fixture

for the condensation (to be provided on site).

Combination Hydro-module H-Generation

Hydro-module H-Generation

Detail view from below

1 Condensation outlet

2 Sealing washer

3 Outlet bend

Outdoor units

IMPORTANT

Also use the following instructions at the time of installation of the condensation outflow hose on

the outdoor unit:

●

When using the outlet bend, the outdoor unit should be mounted on a sub-base at

least 50 mm in height.

●

For installation of the outdoor unit on a foundation, the installation method with a

strip foundation and gravel filling is recommended (

→

5.2.2.3 Securing the outdoor

unit, p. 92

). For a safe drainage of condensation water, even at outside tempera

tures below 0 °C, a drain pipe is recommended, reaching into the frost-free area of

the underground.

Summary of Contents for Aquarea B1






















































































































Search results

Summary of Contents for Aquarea B1

Reviews:

Related manuals for Aquarea B1

Brands by name

Popular brands

Panasonic Aquarea B1, Planning And Installation Manual

Search results

Summary of Contents for Aquarea B1

Reviews:

Related manuals for Aquarea B1

Brands by name

Popular brands