Panasonic Aquarea B1 Planning And Installation Manual Download Page 59

Page: 59 / 117

112

Aquarea air-to-water heat pumps - Planning and installation manual - 01/2018

Planning

113

Aquarea air-to-water heat pumps - Planning and installation manual - 01/2018

Planning

For the hydro-module WH-SDC12H6E5, WH-SDC16H6E5:

● Mains supply 1 of this device fulfils EN/IEC 61000-3-12, provided that the short-cir

cuit power S

at the transfer point of the energy provider to the operator is greater

than or equal to 2200 kW. The installer or operator of the device is, therefore,

responsible for ensuring, in case a consultation with the EVU is needed, that the

device is only connected, if the short-circuit power S

is greater than or equal to

2200 kW.

● Mains supply 1 of the device fulfils ICE/ EN 61000-3-11 and is to be connected to

a suitable voltage source, which has a current rating ≥100 A per phase. Connect

to the EVU to ensure that the current rating at the transfer point is sufficient for the

device.

● Mains supply 2 of this device fulfils EN/ IEC 61000-3-12.

● Mains supply 2 of the device fulfils IEC/EN 61000-3-11 and is to be connected to a

suitable voltage source, which has a maximum permissible system impedance of

max

= 0.271 Ω at the transfer point. Connect to the EVU to ensure that the mains

supply 2 is only connected to a grid with the maximum of this impedance.

For the hydro-module WH-SXC09H3E5, WH-SXC12H6E5:

● Mains supply 1 of this device fulfils EN/IEC 61000-3-12, provided that the short-cir

cuit power S

at the transfer point of the energy provider to the operator is greater

than or equal to 1700 kW. The installer or operator of the device is, therefore,

responsible for ensuring, in case a consultation with the EVU is needed, that the

device is only connected, if the short-circuit power S

is greater than or equal to

1700 kW.

● Mains supply 1 of the device fulfils ICE/ EN 61000-3-11 and is to be connected to

a suitable voltage source, which has a current rating ≥100 A per phase. Connect

to the EVU to ensure that the current rating at the transfer point is sufficient for the

device.

● Mains supply 2 of this device fulfils EN/ IEC 61000-3-12.

● Mains supply 2 of the device fulfils IEC/EN 61000-3-11 and is to be connected to a

suitable voltage source, which has a maximum permissible system impedance of

max

= 0.271 Ω at the transfer point. Connect to the EVU to ensure that the mains

supply 2 is only connected to a grid with the maximum of this impedance.

For the hydro-modules WH-SDC12H9E8, WH-SDC16H9E8, WH-SXC12H9E8,

WH-SXC16H9E8, WH-SQC12H9E8 and WH-SQC16H9E8:

● Mains supply 1 of this device fulfils EN/ IEC 61000-3-2.

● Mains supply 1 of this device fulfils EN/ IEC 61000-3-3 and can be connected to

the current supply grid.

● Mains supply 2 of this device fulfils EN/ IEC 61000-3-2.

● Mains supply 1 of this device fulfils EN/ IEC 61000-3-3 and can be connected to

the current supply grid.

Compact systems

Models

Mains connection 1

Mains connection 2

Phases

Max. current

consumption (A)

Max. power

consumption (kW)

Phases

Max. current

consumption (A)

Max. power

consumption (kW)

WH-MDC05H3E5

19.5

4.26

13.0

3.0

WH-MDC07H3E5

20.5

4.48

13.0

3.0

WH-MDC09H3E5

22.9

5.01

13.0

3.0

WH-MXC09H3E5

25.0

5.41

13.0

3.0

WH-MXC12H6E5

29.0

6.27

26.0

6.0

WH-MHF09G3E5

28.5

6.09

13.0

3.0

WH-MHF12G6E5

29.0

6.20

26.0

6.0

FI protection switch and mains connections

L N

FI protection

switch

Mains connections

Mains connection 1 Mains connection 2

Terminals on compact device

Terminals on disconnector of the mains connection

Models

Mains connection 1

Mains connection 2

Phases

Max. current

consumption (A)

Max. power

consumption (kW)

Phases

Max. current

consumption (A)

Max. power

consumption (kW)

WH-MXC09H3E8

14.7

9.85

13.0

3.0

WH-MHF09G3E8

14.5

9.67

13.0

3.0

FI protection switch and mains connections

FI protection

switch

Mains connections

Mains connection 1

Mains connection 2

Terminals on compact device

Terminals on disconnector of the mains connection

Summary of Contents for Aquarea B1






















































































































Search results

Summary of Contents for Aquarea B1

Reviews:

Related manuals for Aquarea B1

Brands by name

Popular brands

Panasonic Aquarea B1, Planning And Installation Manual

Search results

Summary of Contents for Aquarea B1

Reviews:

Related manuals for Aquarea B1

Brands by name

Popular brands