Panasonic Aquarea B1 Planning And Installation Manual Download Page 104

Page: 104 / 117

200

Aquarea air-to-water heat pumps - Planning and installation manual - 01/2018

Maintenance

201

Aquarea air-to-water heat pumps - Planning and installation manual - 01/2018

Maintenance

7.5 Checking of the FI protection switch

WARNING

Danger to life from electric shock!

Life-threatening voltage levels are present in the device.

►

Take care not to touch any live device parts. Only touch the buttons of the FI protec-

tion switch.

Carry out the following steps:

1.  Set the FI protection switch to ON.
7.  Switch on the electricity supply of the indoor unit or compact device.
8.  Press the TEST button on the FI protection switch.

If the FI protection switch is in perfect working order, the lever must be pointing down-

wards to the OFF (green) position. If this is not the case, contact an authorised dealer.

9. Interrupt the electricity supply of the hydro-module again.

10. Set the lever of the FI protection switch to ON again.

11. Switch the electricity supply of the indoor unit or compact device off again.

7.6 Checking of the quick vent valve and venting the system

Carry out the following steps:

1. Open the quick vent valve (

) by turning the valve cap (

) of the quick vent valve one

full turn in an anti-clockwise direction (

→

4.6.2.1 Components (split systems), p. 32

→

4.6.3.1 Components (compact systems), p. 47

1 Quick vent valve

2 Valve cap

Air should now be heard escaping.

12. Repeat the sequence until there are no audible sounds of escaping air.
13. Close the quick vent valve again by turning in a clockwise direction.

7.7 Resetting the thermostatic overload protection

The overload protection (

→

4.6.2.1 Components (split systems), p. 32

→

4.6.3.1 Compo-

nents (compact systems), p. 47

) protects the system against any superheat of the water.

If the thermostatic overload protection is triggered due to the water temperature being too high,

carry out the following steps in order to reset it:

1. Remove the overload protection cover.

14. Using a test pin, press the button (

) lightly in the centre in order to reset the thermostatic

overload protection.

1 Overload protection

2 Button

3 Press

15. Resecure the cover again afterwards.

7.8 Carrying out maintenance work on the cooling circuit

CAUTION

Danger of injury due to unprofessional handling of coolants

Unprofessional handling of coolants leads to various dangers of injury such as freezing, fire and

the danger of explosions and the danger of injury occurring.

►

Working with the coolant must be done by a trained skilled person or an authorised

dealer with refrigerant certification.

►

Observe all the Safety Notices in force for the respective coolant (R410A or R407C).

►

Before commencing work on the cooling circuit, the coolant must always be pumped

out first.

Note

Instructions for switching on the pumping-out operation as well as operating the devices can be

found in the operating instructions for the respective device and in the Appendix to this Manual

(

→

8.1 Extract from the operating instructions (H-Generation), p. 203

Summary of Contents for Aquarea B1






















































































































Search results

Summary of Contents for Aquarea B1

Reviews:

Related manuals for Aquarea B1

Brands by name

Popular brands

Panasonic Aquarea B1, Planning And Installation Manual

Search results

Summary of Contents for Aquarea B1

Reviews:

Related manuals for Aquarea B1

Brands by name

Popular brands