Panasonic Aquarea B1 Planning And Installation Manual Download Page 91

Page: 91 / 117

174

Aquarea air-to-water heat pumps - Planning and installation manual - 01/2018

Installation

175

Aquarea air-to-water heat pumps - Planning and installation manual - 01/2018

Installation

Installation example: Hydro-module WH-SDC03H3E5-1

3+b

A Connection of the power cord

1 FI switch for mains connection 1

2 FI switch for mains connection 2

3 Cable holders / cable reliefs

4 Terminal strip for connecting cable indoor unit /

outdoor unit

B Detailed view: Cable glands

5 Cable gland for power cord 1 and 2 for the connect-

ing cable between indoor and outdoor unit

6+7 Cable glands for control pipelines from optional

accessories

a Use separate cable glands for power cord and

accessory cables

b Fixing power cord with cable holders /cable reliefs

c Leave ground connector longer than the other

cables for safety reasons

6.8.1

Connecting power cord

6.8.1.1

Connecting the power cord to the indoor unit

The following method is applicable as appropriate for all indoor units, combination hydro-mod-

ules and hydro-modules of all generations, but will be explained here on the basis of the exam-

ple of a hydro-module of the H-Generation (

→

Installation example: Hydro-module, p. 175

Carry out the following steps to connect the power cord to the indoor unit:

1. Open the indoor unit (

→

6.5 Opening devices, p. 148

) and, if applicable, the connection

box.

2. Guide the cable through the cable gland (

) into the device.

Secure the cable by means of the cable holder (cable reliefs) (

4. Connect the power cords 1 and 2 accordingly to mains connection 1 and 2 (

), accord

ing to the installation example below (see below) and the connection diagram following it

and ensure that the ground connector is longer than the other cables in every case (

5. Connect the connecting cable to the outdoor unit on the indoor unit terminal (

) and take

care to leave the ground connector longer than the other cables (

). Also ensure that

you connect conductors of the same cable colour to outdoor and indoor unit to the same

terminal number.

6. Connect the other end of the power cord to the power grid via the separator which is

absolutely required in all cases.

7. Secure the individual mains connections according to the cable cross section and the

maximum power consumption. Note that the separation distance between the poles must

be a minimum of 3.0 mm.

Summary of Contents for Aquarea B1






















































































































Search results

Summary of Contents for Aquarea B1

Reviews:

Related manuals for Aquarea B1

Brands by name

Popular brands

Panasonic Aquarea B1, Planning And Installation Manual

Search results

Summary of Contents for Aquarea B1

Reviews:

Related manuals for Aquarea B1

Brands by name

Popular brands