Panasonic Aquarea B1 Planning And Installation Manual Download Page 60

Page: 60 / 117

114

Aquarea air-to-water heat pumps - Planning and installation manual - 01/2018

Planning

115

Aquarea air-to-water heat pumps - Planning and installation manual - 01/2018

Planning

Models

Mains connection 1

Mains connection 2

Phases

Max. current

consumption (A)

Max. power

consumption (kW)

Phases

Max. current

consumption (A)

Max. power

consumption (kW)

WH-MXC12H9E8

11.9

7.91

13.0

9.0

WH-MXC16H9E8

15.5

10.27

13.0

9.0

WH-MHF12G9E8

10.8

7.07

13.0

9.0

FI protection switch and mains connections

FI protection

switch

Mains connections

Mains connection 1

Mains connection 2

Terminals on compact device

Terminals on disconnector of the mains connection

Connection conditions

For compact devices of the H generation

●

For the connection to the electricity supply, use an approved power cord with poly-

chloroprene material, symbol 60245 IEC 57 or higher, for mains connection.

For the compact device WH-MDC05H3E5:

● Mains supply 1 of this device fulfils EN/ IEC 61000-3-2.

● Mains supply 1 of this device fulfils EN/ IEC 61000-3-3 and can be connected to

the current supply grid.

● Mains supply 2 of this device fulfils EN/ IEC 61000-3-2.

● The main supply 2 of this device fulfills IEC/EN 61000-3-11 and is to be connected

to a suitable voltage source, whose maximum allowed system impedance at the

interface is Z

max

= 0.257 Ω. Connect to the EVU to ensure that the mains supply 2

is only connected to a grid with the maximum of this impedance.

For the compact devices WH-MDC07H3E5 and WH-MDC09H3E5:

● Mains supply 1 of this device fulfils EN/IEC 61000-3-12, provided that the short-cir

cuit power S

at the transfer point of the energy provider to the operator is great-

er than or equal to 750 kW. The installer or operator of the device is, therefore,

responsible for ensuring, in case a consultation with the EVU is needed, that the

device is only connected, if the short-circuit power S

is greater than or equal to

750 kW.

● Mains supply 1 of the device fulfils ICE/ EN 61000-3-11 and is to be connected to

a suitable voltage source, which has a current rating ≥100 A per phase. Connect

to the EVU to ensure that the current rating at the transfer point is sufficient for the

device.

● Mains supply 2 of this device fulfils EN/ IEC 61000-3-2.

● The main supply 2 of this device fulfills IEC/EN 61000-3-11 and is to be connected

to a suitable voltage source, whose maximum allowed system impedance at the

interface is Z

max

= 0.257 Ω. Connect to the EVU to ensure that the mains supply 2

is only connected to a grid with the maximum of this impedance.

For the compact devices WH-MXC09H3E5 and WH-MXC12H6E5:

● Mains supply 1 of this device fulfils EN/IEC 61000-3-12, provided that the short-cir

cuit power S

at the transfer point of the energy provider to the operator is greater

than or equal to 1700 kW. The installer or operator of the device is, therefore,

responsible for ensuring, in case a consultation with the EVU is needed, that the

device is only connected, if the short-circuit power S

is greater than or equal to

1700 kW.

● Mains supply 1 of the device fulfils ICE/ EN 61000-3-11 and is to be connected to

a suitable voltage source, which has a current rating ≥100 A per phase. Connect

to the EVU to ensure that the current rating at the transfer point is sufficient for the

device.

● Mains supply 2 of this device fulfils EN/ IEC 61000-3-12.

● The main supply 2 of this device fulfills IEC/EN 61000-3-11 and is to be connected

to a suitable voltage source, whose maximum allowed system impedance at the

interface is Z

max

= 0.453 Ω. Connect to the EVU to ensure that the mains supply 2

is only connected to a grid with the maximum of this impedance.

For the compact devices WH-MXC09H3E8, WH-MXC16H9E8 and WH-MHF09G3E8:

● Mains supply 1 and mains supply 2 of this device fulfils EN/ IEC 61000-3-2.

● Mains supply 1 and mains supply 2 of this device fulfils EN/ IEC 61000-3-3 and can

be connected to the current supply grid.

For the compact devices WH-MXC12H9E8 and WH-MHF12G9E8:

● Mains supply 1 of this device fulfils EN/ IEC 61000-3-2.

● Mains supply 1 of this device fulfils EN/ IEC 61000-3-3 and can be connected to

the current supply grid.

● Mains supply 2 of this device fulfils EN/ IEC 61000-3-2.

● The main supply 2 of this device fulfills IEC/EN 61000-3-11 and is to be connected

to a suitable voltage source, whose maximum allowed system impedance at the

interface is Z

max

= 0.449 Ω. Connect to the EVU to ensure that the mains supply 2

is only connected to a grid with the maximum of this impedance.

For the compact devices WH-MHF09G3E5 and WH-MHF12G6E5:

● Mains supply 1 of this device fulfils EN/IEC 61000-3-12, provided that the short-cir

cuit power S

at the transfer point of the energy provider to the operator is greater

than or equal to 1200 kW. The installer or operator of the device is, therefore,

responsible for ensuring, in case a consultation with the EVU is needed, that the

device is only connected, if the short-circuit power S

is greater than or equal to

1200 kW.

● Mains supply 1 of the device fulfils ICE/ EN 61000-3-11 and is to be connected to

a suitable voltage source, which has a current rating ≥100 A per phase. Connect

to the EVU to ensure that the current rating at the transfer point is sufficient for the

device.

● Mains supply 2 of this device fulfils EN/ IEC 61000-3-12.

● The main supply 2 of this device fulfills IEC/EN 61000-3-11 and is to be connected

to a suitable voltage source, whose maximum allowed system impedance at the

interface is Z

max

= 0.257 Ω. Connect to the EVU to ensure that the mains supply 2

is only connected to a grid with the maximum of this impedance.

Summary of Contents for Aquarea B1






















































































































Search results

Summary of Contents for Aquarea B1

Reviews:

Related manuals for Aquarea B1

Brands by name

Popular brands

Panasonic Aquarea B1, Planning And Installation Manual

Search results

Summary of Contents for Aquarea B1

Reviews:

Related manuals for Aquarea B1

Brands by name

Popular brands