Panasonic Aquarea B1 Planning And Installation Manual Download Page 84 | Manualshive

Page: 84 / 117

background image

160

Aquarea air-to-water heat pumps - Planning and installation manual - 01/2018

Installation

161

Aquarea air-to-water heat pumps - Planning and installation manual - 01/2018

Installation

6.7

Connecting the heating circuit

CAUTION

Danger of illnesses caused by colonies of bacteria in the water

The risk of colonies of bacteria, particularly of Legionella, in the water can be raised with an

open water circuit.

►

Only deploy devices in a closed water system.

CAUTION

Danger of water pipes freezing in outside temperatures below 0 °C

If the heating circuit in the compact system is filled with water and the outside temperature falls

below 0 °C, the risk exists in the compact system that the water pipes may freeze. This can

cause a lot of damage to the device.
The client should therefore ensure the absence of frost by taking

one

of the following

measures:

► Operate the heating circuit using a food-safe antifreeze mixture (propylene glycol).

►

Provide an additional cabinet heating in the compact device to prevent the heating

circuit from freezing up.

► Empty the heating circuit by using a built-in device (manually or automatically) before

freezing starts.

Danger of corrosion in open systems

In the case of open systems, oxygen entry can cause excessive corrosion of the pipelines and

subsequent problems in operation.

►

Install devices only in closed systems without direct contact of the heating water to the

ambient air.

Danger of damage to the hydro-module and other components of the system due to im-

proper working methods when connecting the water heating circuit

To avoid damage to the water-side system components, observe the following instructions:

►

Ensure that the components installed in the water circuit can withstand high operating

water pressures. Use only suitable sealants that are capable of withstanding the pres-

sure and the temperature of the system.

►

Do not use worn out pipes.

►

Lock line ends in bushing through walls so that dirt does not enter the lines.

►

Flush the water-side pipeline before connecting the device to remove contaminants,

because impurities can damage device components.

Model

Note

Refrigerant - hot gas pipeline

Coolant - fluid pipeline

Diameter

mm (inches)

Torque

Nm

Diameter

mm (inches)

Torque

Nm

T-CAP

WH-ADC12 WH-UX09HE5

15.88 (5/8)

65

9.52 (3/8)

42

WH-ADC12 WH-UX12HE5
WH-ADC09 WH-UX09HE8
WH-ADC09 WH-UX12HE8
WH-ADC09 WH-UX16HE8
WH-ADC09 WH-UQ09HE8
WH-ADC09 WH-UQ12HE8
WH-ADC09 WH-UQ16HE8
WH-SXC WH-UX09HE5
WH-SXC WH-UX12HE5
WH-SXC WH-UX09HE8
WH-SXC WH-UX12HE8
WH-SXC WH-UX16HE8
WH-SQC WH-UQ09HE8
WH-SQC WH-UQ12HE8
WH-SQC WH-UQ16HE8

HT

WH-SHF WH-UH09FE5

15.88 (5/8)

65

9.52 (3/8)

42

WH-SHF WH-UH12FE5
WH-SHF WH-UH09FE8
WH-SHF WH-UH12FE8

1 In these indoor unit/outdoor unit combinations, the reducer piece, supplied as part of the scope of delivery of the

combination hydro-module, must be installed in the suction gas pipeline.

«
...
82
83
84
85
86
...
»

Summary of Contents for Aquarea B1






















































































































Reviews:

No comments

Related manuals for Aquarea B1

Brand: Harry Taylor Pages: 56

Brand: Harry Taylor Pages: 52

Brand: VEAB Heat Tech Pages: 40

Brand: YANGTECH Pages: 16

Brand: D-D The Aquarium Solution Pages: 8

Brand: Danfoss Pages: 26

Brand: Calpeda Pages: 80

Brand: Danfoss Pages: 24

Brand: Oerlikon Barmag Pages: 36

Brand: Zenit Pages: 136

Laser 72 Type E

Brand: Toyostove Pages: 31

Brand: IDEAL Pages: 30

Brand: Duraflame Pages: 28

Brand: Lifepro Pages: 13

BLACKLIGHT 7815

Brand: MO-EL Pages: 12

Brand: Calorex Pages: 2

Brand: Astral Pool Pages: 35

Brand: ARDES Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands