Panasonic Aquarea B1 Planning And Installation Manual Download Page 106

Page: 106 / 117

203

Aquarea air-to-water heat pumps - Planning and installation manual - 01/2018

Appendix

8 Appendix

8.1 Extract from the operating instructions (H-Generation)

Keys and display of the operating unit

Keys/display

Quick menu Key

(Further details are to be found in the

separate Quick menu instructions.)

Back Key

Returns to the previous screen

LCD display

Main menu Key

Used to set the function

ON/OFF Key

Used to switch the device on or off.

Operating display

Is illuminated during operation and flashes if

a fault is detected.

Press the

middle of the

keys

No gloves

No stylus

5
6

Hash keys

Are used to select an option.

“Enter” Key

Confirms the content selected.

Upwards

Downwards

Left

Right

Summary of Contents for Aquarea B1






















































































































Search results

Summary of Contents for Aquarea B1

Reviews:

Related manuals for Aquarea B1

Brands by name

Popular brands

Panasonic Aquarea B1, Planning And Installation Manual

Search results

Summary of Contents for Aquarea B1

Reviews:

Related manuals for Aquarea B1

Brands by name

Popular brands