140
Aquarea air-to-water heat pumps - Planning and installation manual - 01/2018
Installation
141
Aquarea air-to-water heat pumps - Planning and installation manual - 01/2018
Installation
6.2
Preparing for installation
Read the following sections carefully before you begin the installation work and follow the in-
structions given in them.
Requirements for installation
Ascertain that all the requirements for installation are met. This includes clearing and defining
the following important aspects during the planning phase (respect the pointers to elaborate
explanations about the respective topic in this manual):
1. Determine the power requirement and the refrigeration requirements for the heating sys-
tem to be installed (
→
5.1 Cooling technique and performance criteria, p. 79
).
2. Based on the performance features of Aquarea air-to-water heat pumps, select the model
suitable for the power requirements (
→
4.6 Functions and technical data, p. 30
).
3. Based on the ambient conditions and the setting up criteria for the various model types,
determine the optimum installation location for the indoor and outdoor unit or the compact
device (
→
5.2 Installation criteria, p. 87
).
4. Determine the requirements for the hydraulic connection of the devices (
→
5.3 Hydrau-
lics, p. 100
). Always conform to the valid legal provisions.
5. Determine the requirements for the electrical connection of the devices (
→
5.4 Electricals,
p. 105
). Always conform to the valid legal provisions.
6. Ensure that the accessories supplied are fully available, e.g. based on the following table.
Owing to the continuous development and improvement of the products, the kind and
range of the accessories supplied can, however, change at any time. So also always
check the list of the accessories supplied in the installation manual accompanying the
device in question.
No. Component
Quantity
Description
Split systems
Compact
systems
with
combination
hydro-module
with
hydro-module
H-Generation /
Standard config.
H-Generation / Version “B”
F-Generation
H-Generation
G-Generation
H-Generation
a
Top mounting plate
1
for F-Generation
●
b
Top mounting plate
1
for H -Generation
●
c
Outlet bend
1
for condensation hose
●
●
●
●
●
●
d
Sealing washer
1
for outlet bend
●
●
●
e
Bottom mounting plate
1
for F-Generation
●
f
Bottom mounting plate
1
for H -Generation
●
g
Screw
3
to fasten the hydro-module to the
bottom mounting plate
●
●
h
Rubber cap
8
●
●
●
i
Cable sleeve
2
●
j
Cover of the operating unit
opening
1
for separate assembly of the
operating unit
●
●
●
k
Adjustable legs
4
●
●
l
Reducing piece
1
●
●
m
Local remote control
1
●
●
1
1 Assembly accessory is to be provided on site.
CAUTION
Danger of the devices being damaged by incorrect coolant
The devices must only be operated with the coolants described in this Manual or the respective
operating instructions. The use of other coolants or coolant compounds can lead to the devices
being damaged and to safety risks. Panasonic will not accept any responsibility or liability what-
soever if incorrect coolants are used.
►
Only use coolant Type R410A for the Aquarea LT and T-CAP series and only Type
R407C coolant for the Aquarea HT series.
►
Do not mix the prescribed coolant with coolants of another type or replace it with a
coolant of another type.
Danger of other material damage to the devices, e.g. due to vibrations, water leaks or fire
►
Any work on the water circuit must be carried out by a trained technician.
►
All relevant European and national provisions (including EN 61770 “Electrical appli-
ances connected to the water mains”) are to be observed in installation work for the
water circuit.
►
Adhere to the conditions prescribed for the installation site:
● Indoor units (hydro-modules or combined hydro-modules) are only to be installed in
indoor areas.
●
Outdoor units and compact devices are only to be installed in outdoor areas.
►
Adhere to the prescribed sequence of installation steps.
► Only use parts and tools delivered with the equipment or as specified.
►
As far as possible, avoid installation of outdoor units and compact devices near the
sea, in regions with a high content of sulphur or at sites where large quantities of oil
(e.g. machine oil, etc.) is present, as this may result in shortened operating life.
Summary of Contents for Aquarea B1
Page 2: ...Notes ...
Page 116: ...Notes Notes ...