manualshive.com logo in svg

NPort Networks N1-9802W, User Manual, Page: 239 / 296

Share
Download
NPort Networks N1-9802W User Manual Download Page 239

 

239 

 

PARAMETERS

：

 

Items 

Description 

ID 

Indicates the index of Statistics entry 

Data 

Source(ifIndex) 

The port ID which wants to be monitored 

Drop 

The total number of events in which packets 

were dropped by the probe due to lack of 

resources 

Octets 

The total number of octets of data(including 

those in bad packets) received on the network 

Pks 

The total number of packets(including bad 

packets, broadcast packets, and multicast 

packets) received. 

Broad-cast 

The total number of good packets received that 

were directed to the broadcast address. 

Multi-cast 

The total number of good packets received that 

were directed to a multicast address 

CRC Errors 

The total number of packets received that had 

a length(excluding framing bits, but including 

FCS octets) of between 64 and 1518 octets, 

inclusive, but had either a bad frame check 

Sequence (FCS) with an integral number of 

octets (FCS Error) or a bad FCS with a 

non-integral number of octets (Alignment 

Error). 

Under-size 

The total number of packets received that were 

less than 64 octets 

Over-size 

The total number of packets received that were 

longer than 1518 octets 

Frag. 

The number of frames which size is less than 

64 octets received with invalid CRC 

Jabb. 

The number of frames which size is larger than 

64 octets received with invalid CRC 

Coll. 

The best estimate of the total number of 

collisions on this Ethernet segment 

64 

The total number of packet( including bad 

packets) received that were 64 octets in length. 

Summary of Contents for N1-9802W









































































































































































































































































































Reviews:

No comments