Nortel RLC Installation And Administration Manual Download Page 143 | Manualshive

Page: 143 / 466

background image

RLC Installation and Administration Guide

117

June 2005

Configuring the host PBX for the RLC

Meridian 1 PBX network port configuration for a Remote Gateway
911x series unit

To support a Remote Gateway 911x series unit on a Meridian 1 PBX, you must
configure the RLC network port using the same procedure as described for PBX
configuration for ATA. Refer to “PBX” on page 114 for details.

Note:

For the CS 2100 PBX, similar configuration rules apply. For

configuration requirements, refer to “CS 2100 configuration requirements” on
page 119.

RLC and Remote Gateway 9150 unit connection paths

The RLC network ports (used to connect to the Remote Gateway 9150 units)
carry HDLC-framed data. You must configure these ports so that they can
transparently pass this data.

Any port you configure as a data port on the Meridian 1 PBX can be an RLC
network port.

If the Meridian 1 PBX, instead of the PSTN or a PTT, provides the Remote
Gateway 9150 unit’s ISDN number, you must configure the line on the host
PBX (LD 27 on the Meridian 1 PBX) as follows:

1

Set B1CT to VCE and DTA.

2

Set B2CT to VCE and DTA.

3

Set USID to 0.

PBX trunks and RLC network ports

When using the Remote Gateway 9100 Series unit with PSTN connectivity, the
PBX trunks must provide data capability. To make sure that the PBX is ready for
data calls, complete the following outlined checkpoints:

1

Use the PRT command in LD20 on the PBX to print out the Network Port
TNs that have been provisioned against the RLC slot. Make note of the
TGAR and NCOS values.

Note:

For specific printing instructions, refer to your PBX documentation.

«
...
141
142
143
144
145
...
»

Summary of Contents for RLC



















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for RLC

Brand: D-Link Pages: 13

Brand: C4i Pages: 8

Brand: Yamaha Pages: 4

Brand: Xinje Pages: 57

Brand: X-Micro Pages: 74

Brand: Ubiquiti Pages: 50

Brand: QNO Pages: 106

Brand: Face Pages: 8

Brand: BSS Audio Pages: 20

Brand: Reeven Pages: 2

Brand: Cypress Semiconductor Pages: 9

Brand: Axis Pages: 104

Brand: Intel Pages: 108

Brand: Caimore Pages: 79

Brand: Garderos Pages: 23

BIC 1I12-P2A25-M30MI1-BPX05-110

Brand: Balluff Pages: 12

Brand: NETGEAR Pages: 2

Brand: Perle Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands