Nortel RLC Installation And Administration Manual Download Page 344 | Manualshive

Page: 344 / 466

background image

318

RLC Installation and Administration Guide

Troubleshooting

Standard 4.0

You can abort the PSTN tests at any time and return the system to normal
operation mode. The start and end of PSTN tests are recorded as display logs. To
view these display logs, access Configuration Manager

→

Alarms/Logs/Stats

→

Display Logs.

If the system reports that it cannot perform PSTN tests, determine the following:

1.

Is the PSTN enabled on the Remote Gateway 9100 Series unit?

2.

Is the Remote Gateway 9100 Series unit enabled?

Note:

During testing, the system reports the status of the test on each RLC

port.The meaning of each status message is shown in the following table:

WARNING

During PSTN testing, do not make any configuration
changes or perform a Save to Flash on the RLC or
Remote Gateway 9100 Series unit involved in the PSTN
testing.

No

Status Message

Comments

1

Trunk up

Link was brought up successfully to the specified
number and Remote Gateway 9100 Series unit port.

2

Attempt Failed

Attempt made to call specified number failed.

3

Port Busy

The specified port is in use and cannot be tested.

4

No Remote Port
Available

There is no Remote Gateway 9100 Series unit port
available to bring up trunk on specified port.

5

Security Failed

There was a security failure while bringing up the trunk.
Check security configuration settings.

6

Abnormal Failure

There is an abnormal failure on this connection due to
errors on the line or an emergency call on the Remote
Gateway 9150 unit.

8

Not Closed

In non-disruptive mode, this trunk bandwidth is being
used for voice calls and could not be freed.

9

Primary not up

If the primary trunk can not be brought up, all additional
trunks show this status.

10

Primary Abnormal Fail

All additional trunks show this message if the primary
trunk experiences an abnormal failure during testing.

11

Not data port

The specified port is not configured as a data port.

12

Attempt by Remote
Failed

Attempt by the Remote Gateway 9100 Series unit to
bring up trunks from remote side failed.

«
...
342
343
344
345
346
...
»

Summary of Contents for RLC



















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for RLC

Brand: XMG Pages: 5

Brand: Habitat Pages: 48

Brand: NAD Pages: 2

Brand: Campbell Pages: 42

ARM Cortex-A9 MPCore

Brand: Dave Embedded Systems Pages: 67

Transportation FiberinMotion

Brand: Radwin Pages: 122

Brand: RadiSys Pages: 44

Brand: Alcad Pages: 6

Brand: VMIC Pages: 126

Brand: dixell Pages: 4

Brand: E-Lins Pages: 9

Brand: Nvidia Pages: 115

Brand: ZyXEL Communications Pages: 2

Brand: Paradyne Pages: 10

Brand: Buffalo Pages: 2

Brand: B&B Electronics Pages: 2

Brand: ETAS Pages: 82

BLKDP45SG - MB 1333FSB DDR3 1333 Aud+Lan RAID SATA ATX

Brand: Intel Pages: 86

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands