Nortel RLC Installation And Administration Manual Download Page 81

Page: 81 / 466

RLC Installation and Administration Guide

June 2005

Planning for RLC installation

RLC Installation Checklist

Page 4 of 7

✔

Task

For details, refer to

3. Hardware and software installation

❒

Install DSP application modules on
the RLC, if required.

“Installing DSP application
modules”.

❒

Install and cable each RLC.

“To install an RLC”

“To cable an RLC”

❒

Install the software from the product
CD-ROM or download the software
from the Nortel web site.

“Installing the software”.

4. RLC configuration

❒

Configure the IP address, subnet
mask, and default gateway on the
RLC.

“Using the Configuration
Wizard to perform initial
configuration”.

❒

If you want to use the PBX’s
administration terminal to administer
the RLC, configure the IP address and
subnet mask of the RLC’s ELAN
port.

“IP Configuration”.

❒

Configure the following items, as
required, to create the communication
paths between the RLC and the
remote unit:

IP network: remote unit’s IP
address

PSTN: remote unit’s telephone
number

security level and, if required,
security identifier

“Using the Configuration
Wizard to perform initial
configuration”

“To configure remote
connection settings”

Summary of Contents for RLC



















































































































































































































































































































































































































































































Search results

Summary of Contents for RLC

Reviews:

Related manuals for RLC

Brands by name

Popular brands

Nortel RLC, Installation And Administration Manual

Search results

Summary of Contents for RLC

Reviews:

Related manuals for RLC

Brands by name

Popular brands