Nortel RLC Installation And Administration Manual Download Page 355

Page: 355 / 466

RLC Installation and Administration Guide

329

June 2005

Planning forms

If the chosen security level is provisioned security, record the security
identifier that each remote unit uses to validate connection requests.

Note:

You must configure the same security level on both the RLC and

remote unit.

On the same form, record the following items for the RLC in the “Reach
Line Card information” section:

IP address, subnet mask, and gateway

security level, and if required, security identifier

If necessary, complete an RLC Online/Offline Table Configuration form for
each remote unit.

Summary of Contents for RLC



















































































































































































































































































































































































































































































Search results

Summary of Contents for RLC

Reviews:

Related manuals for RLC

Brands by name

Popular brands

Nortel RLC, Installation And Administration Manual

Search results

Summary of Contents for RLC

Reviews:

Related manuals for RLC

Brands by name

Popular brands