Nortel RLC Installation And Administration Manual Download Page 296

Page: 296 / 466

270

RLC Installation and Administration Guide

Administration

Standard 4.0

DSP Statistics field descriptions

The following table describes the statistics on the DSP Statistics screen:

Statistic

Description

Single Digit Device ID

Identifies an internal sequence number for indexing
this DSP device among all others on the RLC.

Module Number

Identifies this DSP Application Module’s module
number on the RLC.
Valid values are 0, 1, 2, 3, and 4.

Device Number

Identifies the DSP device that processed the call.

In Service

Identifies any voice channels operating on this DSP
application module.

Total MIPS

Identifies the total millions of instructions per
second (MIPS) capacity for this DSP device.

Available Mips

Identifies the millions of instructions per second
(MIPS) currently available on this DSP device.

Total Channels

Identifies the total channel capacity for this DSP
device.

Total Voice Channels

Identifies the total voice channel capacity for this
DSP device.

Available Voice
Channels

Identifies the number of unused voice channels on
this DSP device.

Total Modem Channels

Identifies the number of channels on this DSP
device that can transmit modem calls.

Summary of Contents for RLC



















































































































































































































































































































































































































































































Search results

Summary of Contents for RLC

Reviews:

Related manuals for RLC

Brands by name

Popular brands

Nortel RLC, Installation And Administration Manual

Search results

Summary of Contents for RLC

Reviews:

Related manuals for RLC

Brands by name

Popular brands