Nikon AF-S VR Micro Nikkor 105mm/f2.8G Repair Manual Download Page 31

Page: 31 / 118

JAA63051-R.3689.A

- A7･ AF-S VR MC 105/2.8G -

#83

(Focus) Encoder brush unit

①

Fix the encoder brush unit on the GMR tape unit

with the screw (#83) temporarily.

GMR tape unit

"∞ (infinity)" position of the
focus pattern.

Encoder brush unit

★

New RJ

②

Rotate the GMR tape unit until the "A" hole is

aligned with the "∞" hole of the inner cam ring of
the fixed tube.

ref

：

The above position of "∞" hole of the cam ring is

almost at the place where the brushes are positioned
at "∞" of the focus pattern.

③

Insert the tool (

★

J11319) in "A" hole.

"A" hole

Infinity positioning pin

★

J11319

④

Loosen the screw (#83) and move the encoder brush

unit from side to side. Adjust so that the contact
surface of the brush is at "∞" position of the focus
pattern.

⑤

Tighten the screw (#83) and apply the screwlock.

⑥

Remove the tool (J11319) from "A" hole.

Adhesive: Screwlock

"∞ (infinity)" position of the
focus pattern.

Summary of Contents for AF-S VR Micro Nikkor 105mm/f2.8G























































































































Search results

Summary of Contents for AF-S VR Micro Nikkor 105mm/f2.8G

Reviews:

Related manuals for AF-S VR Micro Nikkor 105mm/f2.8G

Brands by name

Popular brands

Nikon AF-S VR Micro Nikkor 105mm/f2.8G, Repair Manual

Search results

Summary of Contents for AF-S VR Micro Nikkor 105mm/f2.8G

Reviews:

Related manuals for AF-S VR Micro Nikkor 105mm/f2.8G

Brands by name

Popular brands