Nikon AF-S VR Micro Nikkor 105mm/f2.8G Repair Manual Download Page 77

Page: 77 / 118

JAA63051-R.3689.A

- A53 ･ AF-S VR MC 105/2.8G -

(4) 1-1st lens-group alignment (for periphery)

Caution: As for products lens, the screwlock is applied around four screws (#142) and the 1-1st lens

group. So wipe the screwlock as far as possible with alcohol, etc, then work on the lens
alignment.

①

Give the four knobs of the 1-1st lens-G alignment tool (

★

J11327) about half-turn counterclockwise from the

position where the knobs are screwed completely.

②

Give the retaining ring of [

★

J11327] about two-turns counterclockwise from the position where the retaining

ring is screwed completely.

③

Screw [

★

J11327] all the way in the filter ring of the lens. Then turn it counterclockwise until the four knobs

of [

★

J11327] are positioned like "X" when viewed from the front. (ref. Pic. 1)

Knob×4

Retaining ring

④

Rotate the retaining ring until the four setscrews (#142) of the 1-1st lens group can be seen.

[The slightly loosened retaining ring is acceptable at the place where the four screws (#142) can be seen.

]

Lens holder

Screw (#142)×4

⑤

Screw each four knobs of [

★

J11327] evenly, and stop screwing until they touch the lens holder.

⑥

Loosen the four screws (#142) with the alignment screwdriver.

1-1st lens-G

Filter ring

Alignment screwdriver

1-1st lens-G alignment tool

（★

J11327

）

Pic. 1

Lens index

Summary of Contents for AF-S VR Micro Nikkor 105mm/f2.8G























































































































Search results

Summary of Contents for AF-S VR Micro Nikkor 105mm/f2.8G

Reviews:

Related manuals for AF-S VR Micro Nikkor 105mm/f2.8G

Brands by name

Popular brands

Nikon AF-S VR Micro Nikkor 105mm/f2.8G, Repair Manual

Search results

Summary of Contents for AF-S VR Micro Nikkor 105mm/f2.8G

Reviews:

Related manuals for AF-S VR Micro Nikkor 105mm/f2.8G

Brands by name

Popular brands