Nikon AF-S VR Micro Nikkor 105mm/f2.8G Repair Manual Download Page 30 | Manualshive

Page: 30 / 118

background image

JAA63051-R.3689.A

- A6･ AF-S VR MC 105/2.8G -

#120

#79

#134

#133

#98×2

#99×2

#96×2

Focus restriction section

①

Assemble the teflon sheet (#120) in the fixed tube.

②

Fix the restriction rubber (#134) and the washer

(#79) on the fixed tube with the screw (#133).

Fixed tube

Adhesive:Lockend B

Fixed tube

Caution 1:
Do NOT touch the tape of the GMR tape unit
directly with hands.
Caution 2:
The ball-bearing visible side of the roller (#99) must
come to the washer (#96)-side.
Caution 3:
The chamfered side of the washer (#96) must come
to the roller (#99)-side.

GMR tape unit

①

Align the concave portion of the GMR tape unit

with the focus restriction portion, then assemble
the GMR tape unit into the fixed tube.

GMR tape unit

Concave

portion

GMR tape

Fixed

tube

Focus restriction section

Adhesive:Lockend B

②

Fix each two pairs [roller (#99) and

washer (#96)] with the screws (#98)
by passing the body of the screws
(#98) through the holes of the GMR
tape unit.

«
...
28
29
30
31
32
...
»

Summary of Contents for AF-S VR Micro Nikkor 105mm/f2.8G























































































































Reviews:

No comments

Related manuals for AF-S VR Micro Nikkor 105mm/f2.8G

Brand: Canon Pages: 143

PowerShot ELPH 310 HS

Brand: Canon Pages: 212

Brand: Canon Pages: 342

Brand: Canon Pages: 11

Brand: Panasonic Pages: 36

DMCFP2 - DIGITAL STILL CAMERA

Brand: Panasonic Pages: 94

Brand: Panasonic Pages: 305

Brand: Panasonic Pages: 48

Brand: Panasonic Pages: 52

Brand: Panasonic Pages: 56

Brand: Panasonic Pages: 40

Brand: Panasonic Pages: 45

DMC-FX48K - Lumix Digital Camera

Brand: Panasonic Pages: 28

DMC-FX37A - Lumix Digital Camera

Brand: Panasonic Pages: 32

Brand: Panasonic Pages: 40

Brand: Panasonic Pages: 36

Brand: Panasonic Pages: 25

Brand: Panasonic Pages: 42

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands