Nikon AF-S VR Micro Nikkor 105mm/f2.8G Repair Manual Download Page 46

Page: 46 / 118

JAA63051-R.3689.A

- A22 ･ AF-S VR MC 105/2.8G -

Name plate

①

Attach the focus window (#94).

(The focus window already has the adhesive double-
coated tape adhered.)

②

Attach the name plate (#95).

（

The name plate already has the adhesive

double-coated tape adhered.)

#94

#95

Change-SW unit

①

Make soldering bridges to joint the change-SW

unit and the SW-FPC.

②

Turn the VR SW of the change-SW unit to OFF, and

assemble the change-SW unit into the lens, and fi x it
with the screw (#132).

Grease: I-40

Change-SW unit

#132

Soldering bridge×4

SW FPC

Summary of Contents for AF-S VR Micro Nikkor 105mm/f2.8G























































































































Search results

Summary of Contents for AF-S VR Micro Nikkor 105mm/f2.8G

Reviews:

Related manuals for AF-S VR Micro Nikkor 105mm/f2.8G

Brands by name

Popular brands

Nikon AF-S VR Micro Nikkor 105mm/f2.8G, Repair Manual

Search results

Summary of Contents for AF-S VR Micro Nikkor 105mm/f2.8G

Reviews:

Related manuals for AF-S VR Micro Nikkor 105mm/f2.8G

Brands by name

Popular brands