Nikon AF-S VR Micro Nikkor 105mm/f2.8G Repair Manual Download Page 105

Page: 105 / 118

JAA63051-R.3689.A

- A81 ･ AF-S VR MC 105/2.8G -

　⑬

The reconfirmation screen is displayed. Click "OK".

　⑭

An hourglass is displayed on the screen, and writing starts.

The below screen is displayed after a few seconds. Turn camera OFF and turn it ON again.
Click "OK", and the adjustment software restarts.

Note: Unless the camera is turned off once, the value that was written in EEPROM is not reflected.

　⑮

When the adjustment software restarts, perform the operations from

②

⑩

again. Check that

"0μm" of the AF position is in focus.

If "0μm" is not in focus, repeat the operations from

②

⑮

If it is not still in focus even after repetition, the written value in EEPROM may be abnormal. So click
"Design value Rewriting" to write the initial value, then proceed with the operations.

Summary of Contents for AF-S VR Micro Nikkor 105mm/f2.8G























































































































Search results

Summary of Contents for AF-S VR Micro Nikkor 105mm/f2.8G

Reviews:

Related manuals for AF-S VR Micro Nikkor 105mm/f2.8G

Brands by name

Popular brands

Nikon AF-S VR Micro Nikkor 105mm/f2.8G, Repair Manual

Search results

Summary of Contents for AF-S VR Micro Nikkor 105mm/f2.8G

Reviews:

Related manuals for AF-S VR Micro Nikkor 105mm/f2.8G

Brands by name

Popular brands