Nikon AF-S VR Micro Nikkor 105mm/f2.8G Repair Manual Download Page 42

Page: 42 / 118

JAA63051-R.3689.A

- A18 ･ AF-S VR MC 105/2.8G -

Bayonet mount (temporary attachment)

①

Put the washer(s) (#176 selected from A-M) by fi tting position of the holes.

②

Insert the aperture lever (#109) of the bayonet mount into the aperture unit by fi tting in the bending part of

the aperture unit.

③

Fix the bayonet mount with the four screws (#136) (temporarily).

#136×4

Direction for
positioning

Grease: I-40

#176A

～

Apply to the edge face of #109.

Aperture unit

#103

#30

#100×2

Bayonet mount

#101

#109

#104

#23

#28

Adhesive: Screwlock

　Adhesive: Lockend

#109

Summary of Contents for AF-S VR Micro Nikkor 105mm/f2.8G























































































































Search results

Summary of Contents for AF-S VR Micro Nikkor 105mm/f2.8G

Reviews:

Related manuals for AF-S VR Micro Nikkor 105mm/f2.8G

Brands by name

Popular brands

Nikon AF-S VR Micro Nikkor 105mm/f2.8G, Repair Manual

Search results

Summary of Contents for AF-S VR Micro Nikkor 105mm/f2.8G

Reviews:

Related manuals for AF-S VR Micro Nikkor 105mm/f2.8G

Brands by name

Popular brands