Nikon AF-S VR Micro Nikkor 105mm/f2.8G Repair Manual Download Page 99

Page: 99 / 118

JAA63051-R.3689.A

- A75 ･ AF-S VR MC 105/2.8G -

300mm

45mm

（+100μm）

（-100μm）

（-50μm）

（0μm）

（+50μm）

Aberration compensation data writing adjustment

・

This adjustment uses the software which calculates the aberration compensation data according to

the feature of lens aberration and writes in EEPROM of the lens, in order to improve the accuracy of
autofocus.

Note: This adjustment is necessary when the main PCB and/or each lens part (glass, lens chamber)

is replaced or when each lens part is disassembled. Be sure to make this adjustment after
completing inspecting and adjusting the main PCB.

(1) Preparation

　　・

Test chart (Self-made tool: ref. Procedure for how to create it.)

　　・

Tripod

　　・

D100

　　・

Personal computer

　　・

USB cable

（

UC-E4

）

　　・

Adjustment software (

AFSVR105

.exe

：

used for the lens optical alignment.)

(2) Procedure for how to create Test chart

　　・

Photocopy the next page and cut out 1 target chart and 5 resolution charts.

（

Target chart

）

（

Resolution chart

）

　　・

As shown below, put each chart in position at the specified spacings.

Note: Only in the center, put the target chart on the central resolution chart.

Summary of Contents for AF-S VR Micro Nikkor 105mm/f2.8G























































































































Search results

Summary of Contents for AF-S VR Micro Nikkor 105mm/f2.8G

Reviews:

Related manuals for AF-S VR Micro Nikkor 105mm/f2.8G

Brands by name

Popular brands

Nikon AF-S VR Micro Nikkor 105mm/f2.8G, Repair Manual

Search results

Summary of Contents for AF-S VR Micro Nikkor 105mm/f2.8G

Reviews:

Related manuals for AF-S VR Micro Nikkor 105mm/f2.8G

Brands by name

Popular brands