Nikon AF-S VR Micro Nikkor 105mm/f2.8G Repair Manual Download Page 28

Page: 28 / 118

JAA63051-R.3689.A

- A4･ AF-S VR MC 105/2.8G -

#78×3

#77A

～

F×3

#76A

～

F×3

#158

#157A

～

①

Rotate the cam ring in the direction of the arrow until the roller (B28) is positioned lowered.

②

Put the 3rd lens-G movement-frame unit inside the cam ring as shown below.

③

Fix three pairs [of the roller (#76 selected from A

F) and the roller (#77 selected from A

F)] with the

three screws (#78).

Caution: Choose rollers

(

#76 and #77) which are slightly tight for each groove.

3rd lens-group movement-frame unit

Roller B28

Cam ring

3rd lens-G movement frame

④

Rotate the cam ring in the direction of the arrow until

the screw hole of the 3rd lens-G movement frame
can be seen from the groove of the aperture unit.

⑤

Fix the roller (#157 selected from A

～

D) with the

screw (#158).

Aperture unit

Cam ring

Summary of Contents for AF-S VR Micro Nikkor 105mm/f2.8G























































































































Search results

Summary of Contents for AF-S VR Micro Nikkor 105mm/f2.8G

Reviews:

Related manuals for AF-S VR Micro Nikkor 105mm/f2.8G

Brands by name

Popular brands

Nikon AF-S VR Micro Nikkor 105mm/f2.8G, Repair Manual

Search results

Summary of Contents for AF-S VR Micro Nikkor 105mm/f2.8G

Reviews:

Related manuals for AF-S VR Micro Nikkor 105mm/f2.8G

Brands by name

Popular brands