Nikon AF-S VR Micro Nikkor 105mm/f2.8G Repair Manual Download Page 21

Page: 21 / 118

JAA63051-R.3689.A

- D19 ･ AF-S VR MC 105/2.8G -

③

Rotate the cam ring in the direction of the arrow until the roller (B28) is positioned

lowered.

④

Take out the three screws (#78).

⑤

Remove the three pairs of the roller (#77 selected from A-F) and the roller (#76

selected from A-F) with the new tool, X-type slim tweezers (

★

J11326), or an

equivalent tool.

⑥

Remove the 3rd lens-G movement frame unit.

3rd lens-group movement-frame unit

Roller (B28)

#78×3

#77A

～

F×3

#76A

～

F×3

Cam ring

3rd lens-G movement frame unit

①

Rotate the cam ring in the direction of the arrow

until the hole of the 3rd lens-G movement frame
unit can be seen from the groove of the aperture
unit.

②

Take out the screw (#158), and remove the roller

(#157A

～

D).

Aperture unit

#158

#157A

～

Cam ring

Approx.1.5mm

Approx.70°

～

80°

★

New tool

● Fold the tip of the X-type slim tweezers
(

★

J11326)

as below, and use it.

Folding of X-type slim

tweezers

Summary of Contents for AF-S VR Micro Nikkor 105mm/f2.8G























































































































Search results

Summary of Contents for AF-S VR Micro Nikkor 105mm/f2.8G

Reviews:

Related manuals for AF-S VR Micro Nikkor 105mm/f2.8G

Brands by name

Popular brands

Nikon AF-S VR Micro Nikkor 105mm/f2.8G, Repair Manual

Search results

Summary of Contents for AF-S VR Micro Nikkor 105mm/f2.8G

Reviews:

Related manuals for AF-S VR Micro Nikkor 105mm/f2.8G

Brands by name

Popular brands