Nikon AF-S VR Micro Nikkor 105mm/f2.8G Repair Manual Download Page 43

Page: 43 / 118

JAA63051-R.3689.A

- A19 ･ AF-S VR MC 105/2.8G -

①

Rotate the focus coupling key in the direction of the arrow all the way

to the limit. (close-end)

②

Mount the tool (J18004-1). Check the aperture diameter by looking

through at the aperture from the opposite side from the bayonet.

Standard (close-side): The remaining aperture blades that can be

seen must be approx. 2 or 3 mm

③

In case the result is out of standard, rotate the focus coupling key to

the infi nity, loosen the screw (#74), and adjust by moving the [#61]

from side to side.

Position adjustment of Aperture lever

J18004-1

Focus coupling key

#61

#74

④

Rotate the focus coupling key to the infi nity.

⑤

Mount the tool (J18004-1). Check the aperture diameter

by looking through at the aperture from the opposite side

from the bayonet.

Standard (infi nity-side): Full open

⑥

In case the result is out of standard, loosen the two

adjustable screws (#100) of the aperture lever, and adjust

by moving the [#23].

⑦

After the adjustment, fi x the two screws (#100) with the

screwlock.

⑧

If the adjustment is made for the infi nity-side, go back to

①

, and check the close-side again.

J18004-1

#100×2

#23

2-3 mm

Adhesive: Screwlock

Summary of Contents for AF-S VR Micro Nikkor 105mm/f2.8G























































































































Search results

Summary of Contents for AF-S VR Micro Nikkor 105mm/f2.8G

Reviews:

Related manuals for AF-S VR Micro Nikkor 105mm/f2.8G

Brands by name

Popular brands

Nikon AF-S VR Micro Nikkor 105mm/f2.8G, Repair Manual

Search results

Summary of Contents for AF-S VR Micro Nikkor 105mm/f2.8G

Reviews:

Related manuals for AF-S VR Micro Nikkor 105mm/f2.8G

Brands by name

Popular brands