Nikon AF-S VR Micro Nikkor 105mm/f2.8G Repair Manual Download Page 97

Page: 97 / 118

JAA63051-R.3689.A

- A73 ･ AF-S VR MC 105/2.8G -

Check

２

Mount the lens on the

equipment (J15380)

Check the vibration width

of laser

What is the reduction rate
of the vibration width?

・

How much does the vibration width reduce, when the VR

mode changes from OFF to ON by the VR-gyro adjustment.

[Cause]

①

Incorrect adjustment value

②

Others

[Measure]

①

Make the lens position

adjustment and the VR

gyro adjustment

②

The electric parts other

than VR may be

defective.

The parts other than VR
may be defective.

More than 1/5

1/5 or less

Summary of Contents for AF-S VR Micro Nikkor 105mm/f2.8G























































































































Search results

Summary of Contents for AF-S VR Micro Nikkor 105mm/f2.8G

Reviews:

Related manuals for AF-S VR Micro Nikkor 105mm/f2.8G

Brands by name

Popular brands

Nikon AF-S VR Micro Nikkor 105mm/f2.8G, Repair Manual

Search results

Summary of Contents for AF-S VR Micro Nikkor 105mm/f2.8G

Reviews:

Related manuals for AF-S VR Micro Nikkor 105mm/f2.8G

Brands by name

Popular brands