Home
/
NetApp
/
HCI
/
Manual

NetApp HCI, Manual

Share

Page: 254 / 363

NetApp HCI Manual Download Page 254



NOTE: Some of the firmware upgrades might cause the console to disconnect and/or
cause your session on the BMC to disconnect. You can log back into the BMC, however
some services, such as the console, may not be available due to the firmware upgrades.
After the upgrades have completed, the node will perform a cold reboot, which can take
approximately five minutes.

14. Log back in to the BMC UI and click

System

to verify the BIOS version and build time after booting to the

OS. If the upgrade completed correctly, you see the new BIOS and BMC versions.



The BIOS version will not show the upgraded version until the node has finished fully
booting.

15. If the node is part of a cluster, complete the steps below. If it is a standalone node, no further action is

needed.

a. Log in to the VMware vCenter web client.

b. Take the host out of maintenance mode. This might show a disconnected red flag. Wait until all

statuses are cleared.

c. Power on any of the remaining VMs that were powered off.

Upgrade firmware on H610C/H615C nodes

The steps vary depending on whether the node is standalone or part of a cluster. The procedure can take
approximately 25 minutes and includes powering the node off, uploading the ISO, flashing the devices, and
powering the node back on after the upgrade.

Steps

1. If your node is part of a cluster, place it in maintenance mode as follows. If not, skip to step 2.

a. Log in to the VMware vCenter web client.

b. Right-click the host (compute node) name and select

Maintenance Mode > Enter Maintenance

Mode

.

c. Click

OK

.

VMs on the host will be migrated to another available host. VM migration can take time depending on
the number of VMs that need to be migrated.



Ensure that all the VMs on the host are migrated before you proceed.

2. Navigate to the BMC UI,

https://BMCIP/#login

, where BMC IP is the IP address of the BMC.

3. Log in using your credentials.

4. Click

Remote Control > Launch KVM (Java)

.

5. In the console window, click

Media > Virtual Media Wizard

.

6. Click

Browse

and select the compute firmware

.iso

file.

«
...
252
253
254
255
256
...
»

Summary of Contents for HCI












































































































































































































































































































































































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands