NEC PD78052 User Manual Download Page 386

Page: 386 / 603

386

CHAPTER 17 SERIAL INTERFACE CHANNEL 0 (

PD78054Y Subseries)

(2) Slave wait release (slave transmission)

Slave wait status is released by WREL flag (bit 2 of interrupt timing specify register (SINT)) setting or

execution of an serial I/O shift register 0 (SIO0) write instruction.

If the slave sends data, the wait is immediately released by execution of an SIO0 write instruction and the

clock rises without the start transmission bit being output in the data line. Therefore, as shown in Figure 17-

25, data should be transmitted by manipulating the P27 output latch through the program. At this time,

control the low-level width ("a" in Figure 17-25) of the first serial clock at the timing used for setting the P27

output latch to 1 after execution of an SIO0 write instruction.

In addition, if the acknowledge signal from the master is not output (if data transmission from the slave is

completed), set 1 in the WREL flag of SINT and release the wait.

For these timings, see Figure 17-23.

Figure 17-25. Slave Wait Release (Transmission)

Writing

FFH

to SIO0

Setting

CSIIF0

Setting
ACKD

Serial reception

ACK

P27

output
latch 1

Setting

CSIIF0

ACK

output

Serial transmission

Write

data

to SIO0

P27

output
latch 0

Wait

release

Software operation

Hardware operation

SCL

Software operation

Hardware operation

Transfer line

Master device operation

Slave device operation

SDA0(SDA1)

Summary of Contents for PD78052




























































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for PD78052

Reviews:

Related manuals for PD78052

Brands by name

Popular brands

NEC PD78052, User Manual

Search results

Summary of Contents for PD78052

Reviews:

Related manuals for PD78052

Brands by name

Popular brands