manualshive.com logo in svg

NEC PD78052, User Manual

The NEC PD78052 user manual is available for free download on our website. This comprehensive manual provides detailed instructions and guidance on operating and maximizing the features of the PD78052. Unlock the full potential of your product with this user manual, exclusively available at manualshive.com.

Share
Download
background image

110

CHAPTER 5   CPU ARCHITECTURE

(d) Auxiliary carry flag (AC)

If the operation result has a carry from bit 3 or a borrow at bit 3, this flag is set (1).  It is reset (0) in all

other cases.

(e) In-service priority flag (ISP)

This flag manages the priority of acknowledgeable maskable vectored interrupts.  When ISP = 0, the

vectored interrupt whose priority is specified by the priority specify flag registers (PR0L, PR0H, and PR1L)

(Refer to 21.3 (3) Priority specify flag registers (PR0L, PR0H, and PR1L)) to be low is disabled.

Whether the interrupt is actually acknowledged is controlled by the status of the interrupt enable flag (IE).

(f)

Carry flag (CY)

This flag stores overflow and underflow upon add/subtract instruction execution.  It stores the shift-out

value upon rotate instruction execution and functions as a bit accumulator during bit manipulation

instruction execution.

(3) Stack pointer (SP)

This is a 16-bit register to hold the start address of the memory stack area.  Only the internal high-speed RAM

area can be set as the stack area.  The following shows the internal high-speed RAM area of each product.

Table 5-4.  Internal High-Speed RAM Area

Part Number

Internal High-Speed RAM Area

µ

PD78052, 78052Y

FD00H to FEFFH

µ

PD78053, 78053Y

FB00H to FEFFH

µ

PD78054, 78054Y

µ

PD78P054

µ

PD78055, 78055Y

µ

PD78056, 78056Y

µ

PD78058, 78058Y

µ

PD78P058, 78P058Y

Summary of Contents for PD78052




























































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for PD78052

M-Audio Computer Quick Start Manual preview
Computer
Brand: M-Audio Pages: 10
Cabletron Systems Netlink FRX8000 Installation And Setup Manual preview
Netlink FRX8000
Brand: Cabletron Systems Pages: 94
Cabletron Systems MMAC-Plus 9E423-24 Reference Manual preview
MMAC-Plus 9E423-24
Brand: Cabletron Systems Pages: 10
Cabletron Systems MMAC-Plus 9A128-01 Management Manual preview
MMAC-Plus 9A128-01
Brand: Cabletron Systems Pages: 22
Cabletron Systems Spectrum EMM-E6 Addendum Manual preview
Spectrum EMM-E6
Brand: Cabletron Systems Pages: 2
Cabletron Systems DLM6C-AA Overview And Setup Manual preview
DLM6C-AA
Brand: Cabletron Systems Pages: 54
Cabletron Systems Cabletron BRIM-F6 User Manual preview
Cabletron BRIM-F6
Brand: Cabletron Systems Pages: 43
Cabletron Systems Netlink FRX4000 Maintenance Manual preview
Netlink FRX4000
Brand: Cabletron Systems Pages: 60
Cabletron Systems 9E132-15 Appendix preview
9E132-15
Brand: Cabletron Systems Pages: 8
Cabletron Systems TRXI-22 Addendum preview
TRXI-22
Brand: Cabletron Systems Pages: 4
Ensemble Designs Avenue Express Control Panel Data Pack preview
Avenue Express Control Panel
Brand: Ensemble Designs Pages: 19
IBASE Technology IB952 Series User Manual preview
IB952 Series
Brand: IBASE Technology Pages: 71
Net to Net Technologies UIM-1000T Installation Instructions preview
UIM-1000T
Brand: Net to Net Technologies Pages: 4
EVOC 6336-STG-YX Manual preview
6336-STG-YX
Brand: EVOC Pages: 57
Enterasys Enterasys Matrix 2G4082-25 Hardware Installation Manual preview
Enterasys Matrix 2G4082-25
Brand: Enterasys Pages: 58
EMS 2000 IDU Series User Manual preview
2000 IDU Series
Brand: EMS Pages: 52
Bose PowerMatch ESPLink Quick Start Manual preview
PowerMatch ESPLink
Brand: Bose Pages: 2
Digisol DG-SR2004 User Manual preview
DG-SR2004
Brand: Digisol Pages: 73

Brands by name

Popular brands

Load more brands