MULTILIFT XR S User And Maintenance Manual Download Page 208

Page: 208 / 210

Cargotec Finland Oy, Multilift

Phone

Telefax

Nesteentie 36, FI-21200 Raisio

Int +358 204 55 2399

Int +358 204 55 2231

Multilift

EC declaration of conformity

of the machinery

(Directive 2006/42/EC, Annex II, part 1, sub A)

Cargotec Finland Oy, Multilift

Nesteentie 36

FI-21200 Raisio

Finland

declare on our sole responsibility that the

Ground Level Demountable Equipment

Mark

Type

Serial number

Manufacturing year

•

complies with the provisions of the

machinery directive 2006/42/EC.

•

also complies with the provisions of the

directive on electromagnetic

compatibility 2004/108/EC as amended.

Summary of Contents for XR S



















































































































































































































Search results

Summary of Contents for XR S

Reviews:

Related manuals for XR S

Brands by name

Popular brands

MULTILIFT XR S, User And Maintenance Manual

Search results

Summary of Contents for XR S

Reviews:

Related manuals for XR S

Brands by name

Popular brands