MULTILIFT XR S User And Maintenance Manual Download Page 174 | Manualshive

Page: 174 / 210

background image

XR21S59 CHU

174

1/2018

113813003

Hooklift Multilift XR21S59 CHU

Service Manual

Oil qualities

Hydraulic system sets many requirements to the hydraulic oil characteristics.

They contain amongst others:

•   Lubrication requirements
•   Oxidation prevention capability
•   Corrosion protection
•   Defoaming quality
•   High viscosity index, in other words, low change of viscosity when the oil is heated.

In order to meet these requirements and qualities, additives are used in oils. Therefore

it is important that the selected oil meets the characteristics for the operating

environment in question. A lower ambient temperature is the same as the lowest starting

temperature.

Note!

Vegetable based bio oils are not allowed to be used. Only synthetic

environment friendly oils that meet the above mentioned

requirements are allowed.

Note!

Do not mix different oil qualities. Mixing of different oils weakens

generally their characteristics. If it is necessary to use an alternative

oil, check with the supplier the characteristics and correspondence

with the recommended oil.

Changing to biodegradable oil

To obtain the best results, the percentage of the mineral oil left in the system should not

exceed 2%. The “Changing to biodegradable oil” –procedure might also apply to new

systems because the hooklift is tested with mineral oil at the factory if otherwise noticed.

«
...
172
173
174
175
176
...
»

Summary of Contents for XR S



















































































































































































































Reviews:

No comments

Related manuals for XR S

Brand: Tascam Pages: 27

Brand: Jay-Lor Pages: 72

Brand: MacDon Pages: 198

Brand: M-Triangel Pages: 6

Brand: ParaBody Pages: 3

Brand: Valiani Pages: 66

Brand: Jackson Pages: 2

Brand: Ideal Heating Pages: 16

Brand: Keithley Pages: 57

Brand: ABB Pages: 106

ARCHISHAPE 2.0 Linear

Brand: Osram Pages: 7

Chlorinsitu-III

Brand: ProMinent Pages: 120

DuraTech 45' 3-Way Retrieval SRL-R

Brand: Falltech Pages: 18

Brand: B-Safety Pages: 2

Brand: CDP Pages: 20

Brand: Zen Pro Pages: 40

Brand: E2S Pages: 8

Orbit Marine IC PRO LED

Brand: Current Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands